Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Dual-Role HID Architecture on nRF5340: BT Central Input with Selectable USB or BT HID Output 0

Hi, I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
19 views

0 replies

Started 3 hours ago
by Lowlanders
Not Answered
Current consumption in nrf52833, sdk version 2.9.0 , not able to use : pm_state_force(0u, &(struct pm_state_info){PM_STATE_SUSPEND_TO_IDLE, 0, 0}); 0

I am getting an error of "undefined reference to `pm_state_force" . Also, the output files, config file is not showing the command : CONFIG_PM =y prj.conf file has : ...
22 views

0 replies

Started 5 hours ago
by Kuldeep Chandel
Not Answered
VDD_EXT on custom board with nRF54H20 0

Hello, We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7). The voltage we see on VDD_EXT is about 1.3V instead...
17 views

0 replies

Started 5 hours ago
by Mykhaylo
Not Answered
how testing of enhanced multi-admin 0

Hi, I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4. Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
14 views

0 replies

Started 6 hours ago
by chiba
Not Answered
Error when flashing nrf5340 custom board in HV DC/DC mode with 3V0 set using a segger jlink plus 0

I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
30 views

0 replies

Started 15 hours ago
by lcj

Recent in Nordic blog

Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018