Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Pin configurations for GPIO pins on NINA-B306-00B nRF52840 BLE module 0

Hello I’m using the NINA-B306-00B BLE module which uses the nRF52840 MCU for a custom board application. The BLE module interacts with two sensors, an accelerometer via SPI...
7 views

0 replies

Started 24 minutes ago
by neeld
Not Answered
Correct way to integrate MQTT wifi sample into an existing project? 0

Hi, SDK: nRF Connect v2.7.0. Hardware: nrf5340 + nrf7002 module ( WT02C40C ) on a custom board. IDE: Visual Studio Code 1.95.3 (obviously with the nRF Connect extension...
7 views

0 replies

Started 52 minutes ago
by __RICHARD__
Not Answered
Confirmation of nRF5340 CC312 Accelerator Usage and Power Consumption Analysis 0

1. When adding CONFIG_PSA_CRYPTO_DRIVER_CC3XX=y to the configuration as shown in the diagram, does it enable the use of the CC310 accelerator? 2. My understanding is...
18 views

0 replies

Started 4 hours ago
by giun.kim
Not Answered
Is it possible to configure a device as a standard BLE server and a PAwR node? Other PAwR limitations? 0

I am currently working on two separate sample repositories: one for a standard 1:1 BLE connection with a mobile phone and another for a PAwR node that transmits data alongside...
17 views

0 replies

Started 4 hours ago
by rbmarcus
Not Answered
Warning when logging a float value 0

Hello, I get a compiler warning when I try to log a float value using the LOG_INF macro in my project. The code I'm using is from the cell-fund course: lesson 6, ex. 1. Toolchain...
26 views

0 replies

Started 5 hours ago
by GoncaloS

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018

Latest guides

Bluetooth low energy: Wireless timer synchronization among nRF5 devices

Audun

Introduction In a variety of use cases there is a need to share a common clock among multiple devices. Such a common clock can be used for many purposes, for example by having each node in a network perform…
- 12 Jul 2016
nRF5x: General PCB design guidelines for nRF52 series

FormerMember

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 11 Jul 2016
Software Development Kit: Migrating to Peer Manager

Øyvind Rønningstad

The tutorial has been updated for SDK v11, which contains the production-ready release of Peer Manager. The original tutorial can be found on this page, below the updated tutorial. #Migrating to Peer…
- 8 Apr 2016
Bluetooth low energy: Bluetooth low energy Characteristics, a beginner's tutorial

MartinBL

Before we begin Table of content Topics that will be covered include: Before we begin Basic theory Attribute tables in nRFConnect Bluetooth Low Energy application Description of the example Adding a…
- 18 Mar 2016
Bluetooth low energy: Bluetooth Smart and the Nordic's Softdevices - Part 2 Connection

Hung Bui

This blog series was created as an attempt to fill in the gap between how Bluetooth Smart is described in the spec and how you can use our APIs and event from our softdevice to do what defined in the spec…
- 1 Feb 2016
Design Examples: Capacitive Touch on the nRF52 series

Einar Thorsrud

Important updates: Due to erratum 84 (COMP: ISOURCE not functional), capacitive sensing using the relaxation oscillator method is not usable in a real product with the nRF52832, as it will only work reliably…
- 31 Jan 2016