Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Failed to clone the repositories when trying to install SDK 2.7.0 0

Hello all, I'm getting stuck on re-installing any SDK and I'm getting the below error. The error: Failed to clone the repositories: Error: HEAD is now at 100befc70c7 [nrf...
6 views

0 replies

Started 13 minutes ago
by SOOK
Not Answered
Cracen drivers preventing some ciphers from being compiled in 0

Hello, I am trying to upgrade my project from ncs 2.1.0 to ncs 2.6.1. I am running into some strange issues with mbedtls and I suspect it's because the same ciphers enabled...
32 views

0 replies

Started 1 hour ago
by alexdr5398
Not Answered
Size of build image for mcuboot with serial or usb DFU enabled? 0

Working on a nrf5340 project, and running into limits of the size of the flash to store my application image along with mcuboot bootloader. I had a mucboot setup that fitted...
11 views

0 replies

Started 2 hours ago
by BrianW
Not Answered
NRF Blinky implementation 0

Hi, I am building an app that connects to the NRF52840 with BLE. The NRF board is attached to an electrocardiogram(ECG) setup, so I am interested in the app being able to...
20 views

0 replies

Started 4 hours ago
by McBorgar69
Not Answered
Read and Write UICR with nrfutil on nRF5340 0

Hello, I tried to read and write the OTP region in UICR of nRF5340 with nrfutil, but got the following output: Any Ideas, what could be the issue here? Does nrfutil...
20 views

0 replies

Started 4 hours ago
by SJahnke

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019