Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF54H20: UICR->OTP for Serial Number Storage - Factory Programming 0

Hi Nordic Team, I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
11 views

0 replies

Started 29 minutes ago
by lammobile
Not Answered
I have problem when i use nRF52840 to make a touchpad 0

Hello, I have made a PCB has 4 buttons and touchpad, now I want to drive all of them. 1. one button for left button of mouse. 2. one button for right button of mouse....
- development
- software
- C
- bluetooth le
- nrf52840
11 views

0 replies

Started 2 hours ago
by Harvey.Zhang
Not Answered
MCUBOOT + NCS 3.0.1 + Snippets won't compile 0

NCS 3.0.1 MCUBOOT nRF52840 I am adding MCUBOOT to the coap_client example, which inlcudes snippets in the build configuration (ci, debug, logging, mtd). The snippets are...
12 views

0 replies

Started 8 hours ago
by Mary
Not Answered
Cannot perform DFU over USB with MCUboot using USB CDC ACM and a nRF52840 0

I'm trying to implement DFU over USB through Serial Recovery, for a custom board using a nRF52840, following the nRF Connect SDK Intermediate Lesson 9: Exercise 4 – DFU over...
- development
- software
- nrf52840
- usb
- dfu
23 views

0 replies

Started 8 hours ago
by LorisRT
Not Answered
nrf54l15 DK Flashing Error 0

I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
22 views

0 replies

Started 10 hours ago
by M

Recent in Nordic blog

FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015