Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Inquiry Regarding Development of the nRF54L Series with NCS Bare Metal and DFU Support 0

Dear Nordic Technical Support Team, I would like to inquire about the following regarding the nRF54L series development: Can I develop for the nRF54L series using...
14 views

0 replies

Started 35 minutes ago
by YI YANRONG
Not Answered
nRF Cloud CoAP shadow GET fails for 7+ hours — DTLS gateway healthy, shadow service unresponsive 0

nRF Cloud — CoAP transport (device shadow) Date of incident: 2026-06-22, ~13:04 UTC — still unresolved at 20:42 UTC (7h38m+) Device: nRF9151, modem firmware mfw_nrf91x1_2...
25 views

0 replies

Started 5 hours ago
by Ajit Kuttikatte
Not Answered
nRF52832 SPI flash init/boot failure 0

We are doing a DFU over BLE with the second MCUboot partition on an external flash. Some times Zephyr can't access the flash after booting, resulting in a bricked device,...
35 views

0 replies

Started 9 hours ago
by Revilo
Not Answered
ECC key derivation and agreement 0

Hey, I am trying to implement ecdh key agreement and derivation, but I am getting PSA_ERROR_INVALID_ARGUMENT (-135) from psa_key_derivation_key_agreement: Any idea what is...
30 views

0 replies

Started 13 hours ago
by thomasGronroos
Not Answered
SAADC t_PWRUP and Burst Mode Sub-Sample Overhead 0

Hi, I have a question regarding the SAADC timing parameters. I could not find an official specification for the SAADC power-up time (t_PWRUP). While measuring it on my...
- development
- software
- adc
- nRF54L15
31 views

0 replies

Started 13 hours ago
by Adnan Ashraf

Recent in the DevZone Blog

FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015