Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF5340 BLE Audio Request for Schematic Review 0

I am designing an ultra-low-power BLE Audio TWS board based on the nRF5340 and have followed the recommended hardware design guidelines throughout the project. This is my...
- Evaluation
- nPM1100
- bluetooth le
- low-power
- rf design
- hardware
- nRF5340
25 views

0 replies

Started 41 minutes ago
by DavidMorina103
Not Answered
b0 fails to boot using swap algorithm in SDK 3.2.1 in nrf5340 0

Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
24 views

0 replies

Started 1 hour ago
by AlejandroM
Not Answered
BLE disconnect reasone 8 0

Hi everyone, I'm using the nRF5340 on a custom PCB board without an external 32 kHz oscillator. On the network core I flashed the hci_ipc sample. For some reason I occasionally...
35 views

0 replies

Started 2 hours ago
by Petar02
Not Answered
DECT NR+ rssi-1 measurement results saturated 0

Hello, I am measuring RSSI values with nrf_modem_dect_phy_rssi(...) from the DECT PHY firmware. The nrf_modem_dect_phy_rssi_event refers to positive values being saturated...
20 views

0 replies

Started 2 hours ago
by dame
Not Answered
DPPI and GPIOTE BLE events on nRF54L15 0

Hi all, I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
41 views

0 replies

Started 4 hours ago
by ArneVds

Recent in the DevZone Blog

Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014
How different BLE packet types influence throughput

Stefan Birnir Sverrisson

There are several types of write operations, write request with authorization, write request without authorization and write command. You can see message sequence charts for those messages here and he…
- 9 Oct 2014
Measuring Lithium battery voltage with nRF51

Stefan Birnir Sverrisson

Here is an example of a hardware setup to measure the voltage on a Lithium battery with a voltage divider and a connected capacitor. The Lithium battery typically has a voltage range of 2.7 - 4.2 V and…
- 2 Oct 2014
Sniffer application for OS X

RK

I've put up on Sourceforge, a Mac OSX application which interfaces with the Nordic BTLE sniffer software and has some of the functionality of the Windows application Nordic ships with that software package…
- 1 Oct 2014