Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Develop Central UART to talk to RedBear Simple Control Arduino board 0

I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...

659 views

0 replies

Started over 9 years ago
by Henry J
Not Answered
Adding a nRF24L01 to a breadboard or stripboard 0

I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
- breadboard
- nrf24l01
1495 views

0 replies

Started over 9 years ago
by Neil Kolban
Not Answered
nRF51822 books, documentation 0

Hello. Can I get a literature to the nRF51 series? I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
- bluetooth low energy
- nrf51822
878 views

0 replies

Started over 9 years ago
by HAKMUN
Not Answered
some connect problem when use hts . 0

hts, HTC phone, nrf tools HTM, nrf51822, every time when it's power up : the once connect: error code 0x7A cann't read characteristic and 0x14 state change. the second...
- hts err manual
704 views

0 replies

Started over 9 years ago
by Liu
Not Answered
4 channel wireless transceiver and 4 RF temperature sensors as a finished product set: 0

Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
- any fcc approved
1062 views

0 replies

Started over 9 years ago
by baha93

Recent in Nordic blog

Taking a deeper dive into Bluetooth 5

esivertsen

The first in a series of blogs that will help educate on what is most important about Bluetooth 5 and take you deeper into the details of how it works and how you can benefit most from using it. Taking…
- 7 Apr 2017
Logging enabled by default in SDK Bluetooth examples

Håvard

Several users have pointed out a sudden flash size increase in some of our Bluetooth examples. We decided to write a quick post here to describe the reason for this and explain how to decrease the size…
- 29 Mar 2017
Monitor Mode Debugging with J-Link and GDB/Eclipse

Daniel Veilleux

The biggest pain point when debugging an application on the nRF51 series is the inability to set breakpoints while the SoftDevice is active without triggering an assert. Although a workaround exists that…
- 29 Mar 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019