Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Problem with SPI CLCK 0

Hey folks, I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...

446 views

0 replies

Started over 9 years ago
by Milad
Not Answered

How can I use Central and Peripheral at the same time? 0

Hi. I am using S130 softdevice version. Basically, I am using NUS Service and make a my own NUS central service as NUS_C. It is correctly work at normal state. When...

1022 views

0 replies

Started over 9 years ago
by FormerMember
Not Answered
Reviwe for circuit using nRF51822 and Chip ANT 0

Hi All, Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf). I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
692 views

0 replies

Started over 9 years ago
by enojeon
Not Answered

nrf24l01+ how does EN_AA work in detail 0

to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet. then i thought that the settings...

538 views

0 replies

Started over 9 years ago
by thomas
Not Answered
Setting "Custom Data" in nRF51-ble-bcast-mesh 0

I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
- advertising
- s110
- nrf51422
- bluetooth low energy
- mesh
- broadcast
- keil
- nrf51822
1634 views

0 replies

Started over 9 years ago
by Ankit

Recent in Nordic blog

Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015
Building kernel for RPi2 with bluetooth_6lowpan for Raspbian

Håkon Alseth

Building kernel for RPi2 with bluetooth_6lowpan In this guide, you will have two choices: Cross-compilation build Native build Choose the one that fits your needs. Cross-compilation is…
- 9 Apr 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019