Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
GPIOTE port event and pin events enable issue simultaneously 0

hi all , how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin) i enable the GPIOTE to trigger interrupt event. one for the keyboard which need multiple...
- gpiote
- nrf51822
1894 views

0 replies

Started over 11 years ago
by steven
Not Answered
Cycle speed and cadence sensor data , even after stopping the cycle ? 0

Hi All, I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem. ...
- nrf51422
- ant
847 views

0 replies

Started over 11 years ago
by Robin
Not Answered

Write and read back the FSR register failed 0

Hello Nordic Team, I have a problem with programming the nRF24LE1 chip. I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...

1134 views

0 replies

Started over 11 years ago
by MasterAlexei
Not Answered
SDK 6.0.0 OTA DFU iOS compatibility 0

Hi, I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
- s110
- bootloader
- jlink
- keil
- dfu
- nrf51822
1529 views

0 replies

Started over 11 years ago
by Florin
Not Answered
GATT database for a server 0

I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
- gatt nrf51822
- bluetooth low energy
1668 views

0 replies

Started over 11 years ago
by kb

Recent in the DevZone Blog

FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015