Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Is Beacon battery condition advertised? 0

Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?

676 views

0 replies

Started over 10 years ago
by nmdjapan
Not Answered
How message can be handled? 0

Hi All I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t. so, can any one please share information...
505 views

0 replies

Started over 10 years ago
by renu
Not Answered

Central App stuck after service discovery 0

I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples. I've modified them to run on the PCA10001...

748 views

0 replies

Started over 10 years ago
by Erik Sanchez
Not Answered

nRF51822 RX device can't receive packet from nRF24L01P TX device 0

Hi All, I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device. nRF24L01P TX device Register settings are as follows; Reg.EN_AA=0x00...

648 views

0 replies

Started over 10 years ago
by Mike
Not Answered
S130 programming for the nRF51822 mkit with gcc on a raspberry pi 0

I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
1076 views

0 replies

Started over 10 years ago
by Jimi Cullen

Recent in Nordic blog

SSID-based Wi-Fi locationing: Comparing performance with other location services

Charlie

With the introduction of the nRF7000 Wi-Fi companion IC, we now offer a complete silicon-to-cloud locationing solution with Wi-Fi, cellular IoT, and GNSS. The nRF7000 is optimized for Wi-Fi network scanning…
- 14 Nov 2023
Introducing TechDocs: Nordic's single source for all technical documentation

Tiago Monte

As engineers and developers creating IoT products, you will rely on various resources to bring your ideas to life. Oftentimes, one of the most indispensable resources gets overlooked, and it's one you…
- 5 Oct 2023
Extend your battery life with nRF Cloud's CoAP interface

Tuomas P

Low power is one of the cornerstones of Nordic’s cellular IoT solution. The nRF91 Series is built from the ground up with ultra-low power consumption in mind, and the nRF Connect SDK provides applications…
- 28 Sep 2023

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019