Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Ztest of bluetooth 0

Hi, i need to run this ztest for bluetooth , kindly guide me . link - Nordic\v1.9.1\zephyr\tests\bluetooth\bluetooth Regards, Shikamaru
368 views

0 replies

Started over 2 years ago
by Shikamaru
Not Answered
What can cause RTC1_IRQHandler() to throw Mesh error 8 at 0x00000000? 0

Dear Nordic Experts, This one's a tough nut to crack: The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
690 views

0 replies

Started over 2 years ago
by BlueMike
Not Answered
CMAC calculation failed with SDK 1.9.1 0

SoC: nRF5340 SDK: nRF Connect SDK 1.9.1 CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1. psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
460 views

0 replies

Started over 2 years ago
by Dan2022
Not Answered
Slides from the Electromaker contest Q&A webinar 0
337 views

0 replies

Started over 2 years ago
by Robin M Saltnes
Not Answered
Antenna 0

Forget it, I have found related document and all is clear.
- development
- antenna
- nRF52820
- hardware
500 views

0 replies

Started over 2 years ago
by bob

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020
Software: Using a custom Secure Partition Manager with your application

Heidi-Irene Harvey Sollie

One of the samples available in the nRF Connect SDK is the Secure Partition Manager, which is required to run applications in the nonsecure domain of the CPU. The sample uses the SPM library available in…
- 12 Feb 2020
Getting Started : nRF Connect SDK Bluetooth Low Energy tutorial part 1: Custom Service in Peripheral role

haakonsh

Scope The goal of this tutorial is to set-up your own custom Bluetooth Low Energy service on an nRF5340 acting in a peripheral role. We will set up a new Bluetooth LE project from scratch. The finished…
- 11 Feb 2020
Mesh Networks: Mass Provisioning of Nordic BLE Mesh Nodes

Mark Q

Purpose When creating a mesh network with many nodes, it can take a while to provision each node, especially using PyACI. An alternative is to use a static provisioner that provisions the nodes automatically…
- 8 Feb 2020
Software and Protocols: Enabling and testing TLS in mqtt_simple

Daniel Veilleux

The MQ Telemetry Transport (MQTT) protocol is hugely popular in IoT because it is lightweight and versatile. In this post we will enable Transport Layer Security (TLS) in the mqtt_simple sample from the…
- 4 Feb 2020
Getting Started: Introduction to Nordic nRF5 SDK and Softdevice

Mihua

What is the difference between SDK and Softdevice? How can we select SDK and Softdevice versions? Do the SoC, SDK, and Softdevice have version compatibility problems? How can we understand the SDK directory…
- 15 Jan 2020