Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
StartServiceDiscovery fails after disconnection (VS10, C#) 0

After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again. IsDeviceDiscoveryOngoing was checked before. The...
- masteremulator
- mcp
- c#
994 views

0 replies

Started over 10 years ago
by Damien
Not Answered

Processing/debugging received data in PCA10000 0

Hi, I wanted to ask a question regarding sending data. I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...

487 views

0 replies

Started over 10 years ago
by john
Not Answered

nRF51822 communicate with nRF2401E 0

Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...

570 views

0 replies

Started over 10 years ago
by flyinggirlxhx
Not Answered
When SLAVE_LATENCY not equal to zero, connect will disconnect sometime. 0

E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard SDK 6.0.0 Softdevice 7.0 When I connect to Android 4.4.3 device(Nexus7 II) will...
- s110
- nrf51822
1026 views

0 replies

Started over 10 years ago
by gootoomoon
Not Answered
when I set SLAVE_LATENCY = 3 or other none zero number,ble connect will disconnect auto 0

E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard SDK 6.0.0 Softdevice 7.0 When I connect to Android 4.4.3 device(Nexus7 II) will...
- s110
- softdevice 7.0
- nrf51822
- sdk 6.0
768 views

0 replies

Started over 10 years ago
by gootoomoon

Recent in Nordic blog

Native support for nRF51 SDK in Keil IDE

Krzysztof Loska

Recently we introduced support for CMSIS-Pack into our nRF51 SDK. The nRF51 SDK is natively supported in the Keil IDE. This means that nRF51 SDK latest version and example software for nRF51 are easily…
- 10 Dec 2014
Programming nRF51 with ST-Link & uVision

Milan

Hi, I am planning to design a device based on nRF51-dk but with external programmer. I have ST-Link available so I thought I just provide a simple walk through showing how to set it up. Firstly, here…
- 10 Dec 2014
Visualising your memory usage

Eliot Stock

The linker in the GCC toolchain, ld, produces a *.Map file which shows you how the memory on your micro is being used. This file is a goldmine of information but it's a bit difficult for humans to absorb…
- 2 Dec 2014

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019