Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

To implement iBeacon what are the things to be take care at the peripheral side. 0

Hi Team, To implement iBeacon what are the things to be take care at the peripheral side. Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...

968 views

0 replies

Started over 10 years ago
by Ibrahim
Not Answered
PCA10001 hex file for proximity app 0

Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
- nrf51822 proximity
778 views

0 replies

Started over 10 years ago
by Fred Roeber
Not Answered

Timeslot API - modify a radio request 0

Hi, What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session? For example,...

1025 views

0 replies

Started over 10 years ago
by Gili Elias
Not Answered
sd_ant_channel_id_set returns NRF_ERROR_INVALID_ADDR 0

Hi, I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
- nrf51422
- ant
847 views

0 replies

Started over 10 years ago
by Paul Damade
Not Answered
ANT Extended Messaging in API 0

Hi, To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
- nrf51422
- ant
- scan
798 views

0 replies

Started over 10 years ago
by Us

Recent in Nordic blog

On nRF Connect for Mobile 2.5, and performance as the root of all... benefit?

Dinesh Harjani

Tell me if this has happened to you before. You open some file, one you haven't touched in a while. This might be because you need to use an API, a coworker of yours wrote. Maybe it's a library or package…
- 20 Apr 2022
micro:bit v2 Pager

Ali Aljaani

In this blog post, we will show you how to build a pager with a micro:bit v2 and nRF Connect SDK. Writing application in C using nRF Connect SDK gives you the highest level of control over the micro:bit…
- 8 Apr 2022
Comparing range with Bluetooth Low Energy of the nRF21540 DK and the nRF52840 DK

Susheel Nuguru

FYI: The video above shows a similar test as this blog post, just using two nRF52840 DKs and two nRF21540 DKs. The blog post uses one nRF52840 DK and two nRF21540 DKs. One of the reasons we did multiple…
- 7 Apr 2022

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019