Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
sd_ant_channel_id_set returns NRF_ERROR_INVALID_ADDR 0

Hi, I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
- nrf51422
- ant
847 views

0 replies

Started over 10 years ago
by Paul Damade
Not Answered
ANT Extended Messaging in API 0

Hi, To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
- nrf51422
- ant
- scan
798 views

0 replies

Started over 10 years ago
by Us
Not Answered

Qualification questions 0

We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...

854 views

0 replies

Started over 10 years ago
by Gus Gustafson
Not Answered
Best way to minimize NRF_ANT_ERROR_TRANSFER_IN_PROGRESS 0

What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
- softdevice
- ant
712 views

0 replies

Started over 10 years ago
by Jason De Lorme
Not Answered

nRF24L01+ transmitting before auto acknowledgement is complete. 0

I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...

1661 views

0 replies

Started over 10 years ago
by David Watson

Recent in Nordic blog

SSID-based Wi-Fi locationing: Comparing performance with other location services

Charlie

With the introduction of the nRF7000 Wi-Fi companion IC, we now offer a complete silicon-to-cloud locationing solution with Wi-Fi, cellular IoT, and GNSS. The nRF7000 is optimized for Wi-Fi network scanning…
- 14 Nov 2023
Introducing TechDocs: Nordic's single source for all technical documentation

Tiago Monte

As engineers and developers creating IoT products, you will rely on various resources to bring your ideas to life. Oftentimes, one of the most indispensable resources gets overlooked, and it's one you…
- 5 Oct 2023
Extend your battery life with nRF Cloud's CoAP interface

Tuomas P

Low power is one of the cornerstones of Nordic’s cellular IoT solution. The nRF91 Series is built from the ground up with ultra-low power consumption in mind, and the nRF Connect SDK provides applications…
- 28 Sep 2023

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019