Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Connect another board over UART from nRF51822 mKit board 0

I am using mbed library to get leg up on development. This is the first time I am writing any MCU application and it sure makes things a lot easier. I am using nRF51822...
- mbed
- uart
- nrf51822
1417 views

0 replies

Started over 10 years ago
by Jigar Patel
Not Answered
HID Service on iOS 0

I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
1960 views

0 replies

Started over 10 years ago
by Adam
Not Answered

the speed of large amount of data 0

int main(void) { uint32_t BufferCount; uint32_t err_code; // Initialize leds_init(); timers_init(); buttons_init(); uart_init(); ble_stack_init(); gap_params_init...

949 views

0 replies

Started over 10 years ago
by fitfuel
Not Answered
Gazell library source code. 0

Hi I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
- gazell
- nrf51822
1499 views

0 replies

Started over 10 years ago
by Firek
Not Answered

PWM / Timer question 0

HI, I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...

3065 views

0 replies

Started over 10 years ago
by Jacques

Recent in Nordic blog

Upgrade RADVD for IoT on Raspberry Pi 2

Jun Qing ZOU

The RADVD deamon in Raspberry pool is version 1.8.5 (up to Raspberry 2015-02-16). root@raspberrypi:~/radvd# apt-cache policy radvd radvd: Installed: 1:1.8.5-1 Candidate: 1:1.8.5-1 Version table…
- 25 May 2015
Workaround needed for TWI driver (nrf_drv_twi) in SDK v8.1 (TWI_COUNT missing)

Hung Bui

In SDK v8.1 we added the TWI driver (nrf_drv_twi.c). Unfortunately the nrf_drv_config.h file wasn't updated correctly with the new driver. The symptom is the error with "TWI_COUNT is missing". Here…
- 20 May 2015
Common FAQs on DFU

Hung Bui

If you are looking for a place to get started with DFU, please have a look at this presentation here and the tutorial here. In this post, we cover some in depth Q&A topics regarding Device Firmware…
- 15 May 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019