Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

sd_evt_get, not able to receive after sd_flash..... 0

Dear Nordic people, I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...

1057 views

0 replies

Started over 10 years ago
by Jan Krejsa
Not Answered

PAN item 56 TWI module lock-up problem and Rev 3 version of the chip 0

Hi, Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422? Also would you happen to have a time frame as to when the Rev 3 will...

875 views

0 replies

Started over 10 years ago
by ray
Not Answered

Why does re-connection occur 2 times？ 0

Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally. several seconds later, Open Bluetooth in the settings again, and observe the settings...

652 views

0 replies

Started over 10 years ago
by ziv
Not Answered

NRF_WDT: Not able to write to registers 0

Hi, I am trying to power off and/or disable a RR[0] with no success. I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...

1225 views

0 replies

Started over 10 years ago
by Fab
Not Answered

Limit number of packets per connection event? 0

Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...

1099 views

0 replies

Started over 10 years ago
by Paolo D

Recent in Nordic blog

FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019