Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

after flash DFU, com3 is not accessable 0

after flash DFU program into pca10001 board, com3 is not accessible, www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png even after I erase all, and re upload soft...

698 views

0 replies

Started over 11 years ago
by julian
Not Answered
Subsequent sd_ble_gattc_read does not return 0

Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP, received 0x16 bytes of data but there is more to read. Next call to sd_ble_gattc_read using the same connection...
- s120
- receive
- bluetooth low energy
- softdevice
- gatt
1554 views

0 replies

Started over 11 years ago
by Mark Mendelsohn
Not Answered

Why Bluetooth Go to system-off mode, sramon can not be stored. 0

Hello： Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...

1378 views

0 replies

Started over 11 years ago
by bugg
Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

654 views

0 replies

Started over 11 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

836 views

0 replies

Started over 11 years ago
by kazuo KATO

Recent in Nordic blog

Multiple channels in RTT

Krzysztof Zaraska

Segger RTT (Real-Time Terminal) supports multiple data channels. RTT Viewer uses channel 0 only, and implements multiple virtual terminals on top of this. The terminal can be switched by SEGGER_RTT_SetTerminal…
- 29 Sep 2017
6 Things to Know about Bluetooth Beacons

Rose Martin

Smartphones and tablets have revolutionized the manner in which people communicate with each other. Mobile applications with location-based features like Bluetooth beacons, WiFi, and GPS are helping people…
- 22 Sep 2017
Creating a Keil project for a Bluetooth Mesh example (Updated for 0.10.0)

Kristian Skordal

Introduction The recently released nRF5 SDK for Bluetooth Mesh does not provide Keil project files for its example projects. Fortunately, it's relatively easy to set up your own project from scratch.…
- 19 Sep 2017
Using millis() like in Arduino.

schef

Here are two simple functions to use when you want to use timestamps for time measurement. uint32_t millis(void) { return(app_timer_cnt_get() / 32.768); } and for comperison of current with given…
- 18 Sep 2017
Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017