Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

797 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1309 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1264 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
890 views

0 replies

Started over 10 years ago
by Pedro Lopes
Not Answered

sd_power_system_off goes directly to main() in sdk5.2 0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

1038 views

0 replies

Started over 10 years ago
by julian

Recent in Nordic blog

Trying OpenWRT Chaos Calmer (15.05 RC3) on Buffalo WZR-600DHP

Jun Qing ZOU

In this post, we try to setup OpenWRT on a Japanese router, Buffalo WZR-600DHP, which has a Atheros AR7161 in side. The officail guide by OpenWRT could be found here: http://wiki.openwrt.org/toh/buffalo…
- 4 Sep 2015
The Art of Pairing

John Leonard

It's an old chestnut the pairing conundrum, how to make it safe and secure yet so simple people aren't left confused and frustrated whilst trying to pair products. Bluetooth Smart currently has 3 pairing…
- 3 Sep 2015
Reprogram the nRF51822 Beacon Kit to work with iOS 8

rvaessen

When I decided to attempt the reprogramming of my nRF51822 Beacon Kit I read several posts related to the task. The information I needed was there but I found it to be a bit scattered. It was difficult…
- 30 Aug 2015

Latest guides

Software Development Kit: Setting up the Timeslot API

Hung Bui

Setting up the Timeslot API When you want to use the radio while still maintaining a BLE connection or have a task that you need to do uninterrupted by radio activity, you can set up a timeslot. The timeslot…
- 27 Jul 2015
Software Development Kit: Radio Notification

Øyvind Karlsen

Radio Notification In this tutorial we will set up a beacon example and modify it to use radio notification. Then we will use radio notification to light a LED when the radio is transmitting. While this…
- 17 Jun 2015
Software Development Kit: Board support package (BSP)

Øyvind Karlsen

Board Support Package In this tutorial we will use the Board Support Package to control hardware peripherals on the nRF51 or nRF52 DK. Required tools Keil 5.20 nRF SDK 11 nRFgo Studio 1.21.…
- 8 Jun 2015
nRF5x: nRF51 series current consumption guide

Stefan Birnir Sverrisson

nRF51 Low power modes and power profiles documentation The low power modes for the nRF51 series are System On and System Off. You can read about them in the nRF51 Series Reference Manual v3.0 sections…
- 1 Jun 2015
Software Development Kit: Setting up device firmware update(DFU) on the nRF5 DK

Stian Røed Hafskjold

###Note: This tutorial is for the legacy DFU module included in SDK version 11 and earlier. To get started with the new DFU included in SDK 12 and above, please see the SDK documentation in the Infocenter…
- 1 Jun 2015
Bluetooth low energy: Bluetooth low energy Advertising, a beginner's tutorial

MartinBL

Before we begin Table of context Before we begin The "Hello world" example Advertising RSSI Addresses Address types Advertising types Bonding Advertising data Scan response data Change Log 2018…
- 31 Mar 2015