Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
CTS (clear to send) event/interrupt for Libuarte driver. 0

Hi, I'm pretty new to microcontroller programming so please correct my wrongs. I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
482 views

0 replies

Started over 2 years ago
by EugeneBrod
Not Answered
When i use DFU update app firmwre,The Serial Port always blocking and DK no repose 0

Hello, Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU: Source: Example/Dfu Target: Blinky(about 180 segment) But...
- development
- software
- mesh
- nrf52840
- dfu
576 views

0 replies

Started over 2 years ago
by Kai777
Not Answered
Custom Board Uart Communication 0

Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
- development
- software
- nRF9160
- configuration
- softdevice
- Other
- product
567 views

0 replies

Started over 2 years ago
by Mmterkc
Not Answered
Adding second element to a server node? 0

I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
605 views

0 replies

Started over 2 years ago
by Abdelaziz
Not Answered
nRF52840 DK (PCA10056) at 1.8V VEXT: Interface MCU sporadically resetting 0

Hi, Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties. ...
611 views

0 replies

Started over 3 years ago
by Norbert

Recent in Nordic blog

nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the…
- 15 Dec 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019