Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Connecting nRF52840 DK to MC3672 Accelerometer and nRF52840 Dongle to Mac 0

Hi, I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
- development
- nrf52840 dongle
- SDK Documentation
- nrf52840 dk
- bluetooth 5
- nrf5 sdk
- spi
- bluetooth le
- nrf52840
- usb
- hardware
659 views

0 replies

Started over 3 years ago
by Jaz
Not Answered
HID Remote and Central . 0

Hi I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 . USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
500 views

0 replies

Started over 3 years ago
by meghna
Not Answered

Please close this thread 0

Please close this thread

483 views

0 replies

Started over 3 years ago
by kerimkilic
Not Answered
NRF52832 SPI and SoftDevice (S132) issue 0

Hello, I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is. The following test works perfectly when SoftDevice...
- software
- s132
- spi
- softdevice
- nrf52832
- production
824 views

0 replies

Started over 3 years ago
by lo
Not Answered
Interfacing with nRF52832 through the Python 'bleak' module on Mac Osx is excruciatingly slow 0

Hello! So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to search for devices...
1216 views

0 replies

Started over 3 years ago
by Julio

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019