Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Matter firmware can not run in custom board(nrf54l15) 0

I have an nRF54L15DK and a custom-designed nRF54L15 board. These two boards use different pins for peripherals. The NCS version used is v2.9.0. I compiled a Matter project...
26 views

0 replies

Started 7 hours ago
by jared_jia
Not Answered
unknow data when use qspi panel 0

Hi all, I applied QSPI driver on NCS 2.4.0 with QSPI LCD panel and I encountered the problem. The red area is the data I sent, but the blue area is not what I sent....
14 views

0 replies

Started 7 hours ago
by Wayne_Chang
Not Answered
How to use nrf54L15-dk with external host through hci uart application 0

Hi, I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
15 views

0 replies

Started 7 hours ago
by Abhinav152
Not Answered
Pin assignment for UART on the nRF54L15DK 0

Hello. I am testing UART connectivity using the nRF54L15DK. After assigning pins to TX and RX, there were combinations that worked fine and combinations that didn't. There...
15 views

0 replies

Started 8 hours ago
by a.da
Not Answered
Some problems about Periodic advertising 0

The scanner can be informed of the synchronization information as soon as it receives an ADV_EXT_IND PDU, and then it can later scan only AUX_SYNC_IND PDUs. at this point...
13 views

0 replies

Started 10 hours ago
by Caesarzhou

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019
Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

Simon

This tutorial uses an outdated version of nRF Connect SDK. We recommend using the latest version of nRF Connect SDK when getting started with development. Please see academy…
- 24 May 2019