Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
the latency, reachability and throughput of the DECT NR+ on the nRF9161-DK 0

How can I please analyse the latency, reachability and throughput of the DECT NR+ on the nRF9161-DK. I urgently need a solution please, it's for my bachelor thesis. Thanks...
27 views

0 replies

Started 11 hours ago
by Ismael Nde
Not Answered
A few notes regarding the nRF Connect SDK v2.8.0 and the nRF Connect & devicetree extensions and the overall experience so far... 0

Hi, I just wanted to note a few things that I found out during the usage of nRF Connect SDK v2.8.0 and its corresponding toolchain. 1. When I create a custom board with...
36 views

0 replies

Started 13 hours ago
by masterLee
Not Answered
NRF5340 QSPI XIP IS25LP128F 0

Hello everyone, I am working on a custom board based on the nRF5340 and need to implement code execution from an external QSPI memory. The board uses the IS25LP128 memory...
25 views

0 replies

Started 13 hours ago
by Andrea Boschetti
Not Answered
Extend number of devices for PAwR (Coded PHY) 0

Hi all ! I'm writing this message because I'm having problems trying to increase the number of devices in PAwR (I use Coded PHY). I based my development on the SDK 2.8...
32 views

0 replies

Started 15 hours ago
by Yannch
Not Answered
Auracast example 0

I am using NCS v2.8.0. After successfully running the headset example with one gateway, one left channel receiver and one right channel receiver am trying to get the Auracast...
27 views

0 replies

Started 16 hours ago
by JeroenT

Recent in Nordic blog

Setting up IPv6 over BLE using nRF52 Series and Contiki OS

wbober

Support for nRF52 Series in Contiki OS is no longer maintained and is pending removal. Please check out nRF52x series support in Zephyr OS which offers BLE over IPv6 connectivity. This tutorial shows you…
- 6 Jul 2016
Accessing the SoftDevice API from Python with pc-ble-driver-py

Carles

A new tool from Nordic has been released, pc-ble-driver-py, which allows Python developers to access the full SoftDevice 2.x.x API from a Python application. Update: Raspberry Pi unofficial build available…
- 23 Jun 2016
NFC tag antenna tuning

FormerMember

NFC principle A NFC system consists of two devices, an active and a passive device. The active device is powered, and induces a magnetic field with a coil inductor antenna. When the passive device is placed…
- 20 Jun 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019