Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to measure the power consumption of NRF5340 0

I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
- development
- software
- nRF53
- nRF5340
639 views

0 replies

Started over 4 years ago
by huangjingyu
Not Answered
Anyone have the Eagle libraries for Taiyo Yuden's EYSNSNZWW (it contains the nRF52811) 0

Any pointers would be welcome. /Trivik
371 views

0 replies

Started over 4 years ago
by saccade
Not Answered
TWIM XFER ERROR 0

Hi, i am using: -nRF 52 DK -nRF 52832 -Sensor of Maxim Integrated -SDK 17.0.2 I have some problems in handling the I2C through the nrfx module. This is my ReadByte...
507 views

0 replies

Started over 4 years ago
by polimarte
Not Answered
IPSP with global IPv6 addresses 0

Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
621 views

0 replies

Started over 4 years ago
by StefanHri
Not Answered
ble_gap_addr_t.addr_type of received advertisement is not correctly set from TxAdd/RxAdd bit from PDU header in SoftDevice 0

<removed> Please delete the post.
387 views

0 replies

Started over 4 years ago
by mtfuji

Recent in Nordic blog

nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the…
- 15 Dec 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019