Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to measure the power consumption of NRF5340 0

I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
- development
- software
- nRF53
- nRF5340
692 views

0 replies

Started over 4 years ago
by huangjingyu
Not Answered
Anyone have the Eagle libraries for Taiyo Yuden's EYSNSNZWW (it contains the nRF52811) 0

Any pointers would be welcome. /Trivik
391 views

0 replies

Started over 4 years ago
by saccade
Not Answered
TWIM XFER ERROR 0

Hi, i am using: -nRF 52 DK -nRF 52832 -Sensor of Maxim Integrated -SDK 17.0.2 I have some problems in handling the I2C through the nrfx module. This is my ReadByte...
567 views

0 replies

Started over 4 years ago
by polimarte
Not Answered
IPSP with global IPv6 addresses 0

Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
668 views

0 replies

Started over 4 years ago
by StefanHri
Not Answered
ble_gap_addr_t.addr_type of received advertisement is not correctly set from TxAdd/RxAdd bit from PDU header in SoftDevice 0

<removed> Please delete the post.
413 views

0 replies

Started over 4 years ago
by mtfuji

Recent in Nordic blog

Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014
How different BLE packet types influence throughput

Stefan Birnir Sverrisson

There are several types of write operations, write request with authorization, write request without authorization and write command. You can see message sequence charts for those messages here and he…
- 9 Oct 2014

Latest guides

Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020
Software: Using a custom Secure Partition Manager with your application

Heidi-Irene Harvey Sollie

One of the samples available in the nRF Connect SDK is the Secure Partition Manager, which is required to run applications in the nonsecure domain of the CPU. The sample uses the SPM library available in…
- 12 Feb 2020
Getting Started : nRF Connect SDK Bluetooth Low Energy tutorial part 1: Custom Service in Peripheral role

haakonsh

Scope The goal of this tutorial is to set-up your own custom Bluetooth Low Energy service on an nRF5340 acting in a peripheral role. We will set up a new Bluetooth LE project from scratch. The finished…
- 11 Feb 2020
Mesh Networks: Mass Provisioning of Nordic BLE Mesh Nodes

Mark Q

Purpose When creating a mesh network with many nodes, it can take a while to provision each node, especially using PyACI. An alternative is to use a static provisioner that provisions the nodes automatically…
- 8 Feb 2020
Software and Protocols: Enabling and testing TLS in mqtt_simple

Daniel Veilleux

The MQ Telemetry Transport (MQTT) protocol is hugely popular in IoT because it is lightweight and versatile. In this post we will enable Transport Layer Security (TLS) in the mqtt_simple sample from the…
- 4 Feb 2020
Getting Started: Introduction to Nordic nRF5 SDK and Softdevice

Mihua

What is the difference between SDK and Softdevice? How can we select SDK and Softdevice versions? Do the SoC, SDK, and Softdevice have version compatibility problems? How can we understand the SDK directory…
- 15 Jan 2020