Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Outdated AT commands? 0

I am trying to send a variety of AT commands to my module and it looks like I am missing something or the documentation is not up to date for some of these: If I try to...
22 views

0 replies

Started 14 hours ago
by Colibri
Not Answered
Using GPS active antenna 0

Hi , I would like to use an external GPS active antenna on the nRF9151 EVB for testing (J2), does it disconnect the on board antenna GPS ? should I connect/disconnect any...
18 views

0 replies

Started 14 hours ago
by ERAN GISSER
Not Answered
Increased power consumption after start up 0

Hi, I am trying to optimize my nrf52840 application for power consumption. If I run simple loop using nrf5 SDK i get ~1.2mA. However with similiar code on Zephyr: I get...
16 views

0 replies

Started 14 hours ago
by Michal
Not Answered
Issue with nRF52840 Dongle Recovery Mode 0

Hello everyone, I'm having an issue with my nRF52840 Dongle. I can detect the device with nrfutil device list command, which shows: > nrfutil device list DC1D9FD62EC5...
- development
- software
- nrf5
- nRF Tools
- flash
- nrf52840
- dfu
30 views

0 replies

Started 15 hours ago
by DavidCarneros
Not Answered
appName in shadow register using CoAP protocol - nRFCloud 0

Hello, I would like to ask how to update the appName field in the shadow register on the nRFCloud, using CoAP protocol. I was able to change the appVersion by passing...
12 views

0 replies

Started 15 hours ago
by Avgerinos89

Recent in Nordic blog

Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019