Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SAADC 0

Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
423 views

0 replies

Started over 5 years ago
by shark
Not Answered
Engineer needed for OTA Project 0

I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU. nRF52810 must have command- and data mode over UART, Pic controler...
335 views

0 replies

Started over 5 years ago
by pschoon
Not Answered
Initialization and operation of sensor mpu6050 with nrf52840 development board 0

I want to be able to read the gyro and accelerometer values from the MPU6050 sensor. As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
- development
- software
- nrf52
- windows
- SDK Documentation
- beginner
- nrf52840 dk
- nRF Tools
- nRF Series products
- C
- nrf52840
- s140
- twi
753 views

0 replies

Started over 5 years ago
by MRK-196
Not Answered
how to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I should use SHA256 and MD5. I made my code as below. NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
724 views

0 replies

Started over 5 years ago
by roger.k
Not Answered
How to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I want to use SHA256 as below. output32Byte = SHA256[input32Byte]; Which function or example can I refer to? And also I want to...
1207 views

0 replies

Started over 5 years ago
by roger.k

Recent in Nordic blog

One tool to rule them all: nRF Util becomes a unified command line utility

Ali Aljaani

nRF Util is Nordic's command line utility for Nordic products. You can easily use it to flash applications onto your Nordic device through a terminal. In the most recent major version update, v7.0.0…
- 5 Jan 2023
Reading Thingy:53 sensor data using Bluetooth LE

Tiago Monte

The Thingy:53 is a bleeding edge IoT prototyping platform featuring the flagship nRF5340 dual-core Wireless SoC. It also contains several sensors and a rechargeable Li-Po battery, making it an excellent…
- 9 Dec 2022
Printing to an I2C OLED display using nRF Connect SDK

helsing

If you are a human, as opposed to a microcontroller, you might want an easy and intuitive way to read out data from your application. Adding a small OLED display to your project is a simple solution for…
- 3 Nov 2022

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019