Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Does the nRF52840DK[PCA10056] support IPSP service serialization (e.g. sd_ble_l2cap_ch_setup) connected with pc-ble-driver? 0

I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
- development
- software
- nrf52840 dk
- softdevice
- bluetooth le
- nrf52840
- s140
661 views

0 replies

Started over 5 years ago
by RyanChu
Not Answered
how to get the data from two uarts in nRF52840 0

hi... i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
665 views

0 replies

Started over 5 years ago
by ps_anu
Not Answered
BLE consumption peripheral to high 0

Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral After the connection I need to save power at the peripheral board, because the cpnsumptio...
605 views

1 reply

Latest over 5 years ago
by Stian Røed Hafskjold
Not Answered
Error:Application memory access +2

In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
742 views

0 replies

Started over 5 years ago
by Panda
Not Answered
NRF52840 based IoT Sensor Board 0

NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
- nrf52840
- hardware
- iot
905 views

0 replies

Started over 5 years ago
by rakwirelessyu

Recent in Nordic blog

Parse MQTT message in Wireshark for IoT test

Jun Qing ZOU

Wireshark (version 1.12.5 at the time of writting) lists MQTT as supported protocol but could not parse it from the TCP payload by default. We can add some plugins to enable it. Download the Wireshark…
- 26 May 2015
Upgrade RADVD for IoT on Raspberry Pi 2

Jun Qing ZOU

The RADVD deamon in Raspberry pool is version 1.8.5 (up to Raspberry 2015-02-16). root@raspberrypi:~/radvd# apt-cache policy radvd radvd: Installed: 1:1.8.5-1 Candidate: 1:1.8.5-1 Version table…
- 25 May 2015
Workaround needed for TWI driver (nrf_drv_twi) in SDK v8.1 (TWI_COUNT missing)

Hung Bui

In SDK v8.1 we added the TWI driver (nrf_drv_twi.c). Unfortunately the nrf_drv_config.h file wasn't updated correctly with the new driver. The symptom is the error with "TWI_COUNT is missing". Here…
- 20 May 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019