Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Initialization and operation of sensor mpu6050 with nrf52840 development board 0

I want to be able to read the gyro and accelerometer values from the MPU6050 sensor. As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
- development
- software
- nrf52
- windows
- SDK Documentation
- beginner
- nrf52840 dk
- nRF Tools
- nRF Series products
- C
- nrf52840
- s140
- twi
779 views

0 replies

Started over 5 years ago
by MRK-196
Not Answered
how to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I should use SHA256 and MD5. I made my code as below. NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
743 views

0 replies

Started over 5 years ago
by roger.k
Not Answered
How to use SHA256 and MD5? 0

Hi. I'm using nRF52832, SDK13.0.0. I want to use SHA256 as below. output32Byte = SHA256[input32Byte]; Which function or example can I refer to? And also I want to...
1228 views

0 replies

Started over 5 years ago
by roger.k
Not Answered
Does the nRF52840DK[PCA10056] support IPSP service serialization (e.g. sd_ble_l2cap_ch_setup) connected with pc-ble-driver? 0

I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
- development
- software
- nrf52840 dk
- softdevice
- bluetooth le
- nrf52840
- s140
622 views

0 replies

Started over 5 years ago
by RyanChu
Not Answered
how to get the data from two uarts in nRF52840 0

hi... i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
637 views

0 replies

Started over 5 years ago
by ps_anu

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019