Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
spi communication issue on nrf5340 custom board 0

Hello. I'm trying to do spi communication on a custom board with nrf5340 used. I'm using three threads, I build it, but if I put it on the board, the board will have a problem...
0 views

0 replies

Started 4 hours ago
by ozoz05
Not Answered
NCS 2.8.0: path length problem during build under Windows 0

Hello, I know that this issue comes up from time to time. I'm raising it again, because to my opinion there have to be a solution for this. Perhaps there is, that's the...
0 views

0 replies

Started 5 hours ago
by rgrr2
Not Answered
Pin configurations for GPIO pins on NINA-B306-00B nRF52840 BLE module 0

Hello I’m using the NINA-B306-00B BLE module which uses the nRF52840 MCU for a custom board application. The BLE module interacts with two sensors, an accelerometer via SPI...
9 views

0 replies

Started 6 hours ago
by neeld
Not Answered
Correct way to integrate MQTT wifi sample into an existing project? 0

Hi, SDK: nRF Connect v2.7.0. Hardware: nrf5340 + nrf7002 module ( WT02C40C ) on a custom board. IDE: Visual Studio Code 1.95.3 (obviously with the nRF Connect extension...
11 views

0 replies

Started 7 hours ago
by __RICHARD__
Not Answered
Confirmation of nRF5340 CC312 Accelerator Usage and Power Consumption Analysis 0

1. When adding CONFIG_PSA_CRYPTO_DRIVER_CC3XX=y to the configuration as shown in the diagram, does it enable the use of the CC310 accelerator? 2. My understanding is...
21 views

0 replies

Started 10 hours ago
by giun.kim

Recent in Nordic blog

Debugging on nrf52840 with GDB from CLI on linux

jfcamel

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017
The KEY POINT of example "ble_app_uart"

QQ645116977

This article baed on "pca10040", nRF52832 example code path "examples/ble_peripheral/ble_app_uart" IMPORTANT!!!! board config file of this example located in "components/boards/pca10040.h" and uart…
- 12 Dec 2017
Introduce smart motion controller - ELIO

caram5555

"ELIO" is a Bluetooth module and smartphone application that can drive motor(DC, Servo) and illuminate LEDs. This module mounts Nordic's nRF52832 and motor controller IC. Smartphone application can create…
- 12 Dec 2017

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020