Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to connect Proxomity , UART and DFU with all at the same time with single connection. 0

Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
- bluetooth low energy
532 views

0 replies

Started over 7 years ago
by Sahil Bharwani
Not Answered

Question about the PDM/PCM of nrf52832 0

Dear Nordic employee: 1、 what do I have? I have a thingy52 develop kit（nrf52832） 2、what is my purpose? the quality of thingy52 audio demo is not good（iphone7）...

1642 views

0 replies

Started over 7 years ago
by victor_CHINA
Not Answered
How to optimize power consumption when UART run? 0

Hello Nordic, My development environment: SDK>> NRF51822_SDK10, SoftDevice>> S130 Example>> ble_app_uart I am looking forward to your reply! Thanks. Best Regards...
- uart power consumption
910 views

0 replies

Started over 7 years ago
by Andy
Not Answered
Unable to start nRF connect(BLE) 0

Dear friends, according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps: Connect a development kit or dongle to...
- ble
- nrfconnect
814 views

0 replies

Started over 7 years ago
by xvhongpeng
Not Answered

MESH sd_ble_enable NRF_ERROR_NO_MEM 0

Hi I have add some function call like sd_ble_enable in mesh example, I test to get then I set the address and all sd_ble_cfg_set is ok but when I call "sd_ble_enable...

1181 views

0 replies

Started over 7 years ago
by mark

Recent in Nordic blog

Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015
How to use the latest Keil 5 for Keil 4 projects (.uvproj)

Stefan Birnir Sverrisson

As many have noticed, Keil 5 does not have native support for Keil 4 projects (project files ending with uvproj), it only has native support for Keil 5 projects (project files ending with uvprojx). However…
- 26 Mar 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019