Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
GPIO port input in low power mode 0

Hello, I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
- nrf51822
1225 views

0 replies

Started over 7 years ago
by michael
Not Answered
Central whitelists with peer manager under FreeRTOS 0

Hi Nordic, I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos. What I see: central app crashes (hardfault...
- peermanager
- s132
- nrf52832
- central
- sdk13
1063 views

0 replies

Started over 7 years ago
by x_mike
Not Answered

Need help for this captured BLE HID key code? 0

Hello All, I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...

1250 views

0 replies

Started over 7 years ago
by alikob
Not Answered

COMMUNICATION BETWEEN TWO NRF51X BOARDS 0

I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...

584 views

0 replies

Started over 7 years ago
by ANKITTY
Not Answered

BLE beacons for sensor data, replay attack & spoofing 0

Hi, I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...

1415 views

0 replies

Started over 7 years ago
by BLE_lp

Recent in Nordic blog

Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015
How to use the latest Keil 5 for Keil 4 projects (.uvproj)

Stefan Birnir Sverrisson

As many have noticed, Keil 5 does not have native support for Keil 4 projects (project files ending with uvproj), it only has native support for Keil 5 projects (project files ending with uvprojx). However…
- 26 Mar 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019