Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
LFXO active with 0.5μA higher current 0

Hi, On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher. I am using a nRF52832 module with the low frequency crystal oscillator...
- nrf52
- s132
- lfxo
675 views

0 replies

Started over 7 years ago
by ALE
Not Answered

Wouldn't update connection params 0

Hi, I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init: static void conn_params_init(void){ uint32_t err_code; ble_conn_params_init_t...

723 views

0 replies

Started over 7 years ago
by Alice
Not Answered
how to use whitelist in ble_app_hrs_c 0

S130, SDK 12.3, ble_app_hrs_c example. I want to use whitelist function in this example but I can't finish it. When I run peer_list_get(), it gets all 0xFF, means that...
- s130
- whitelist
- ble_app_hrs_c
- nrf51822
885 views

0 replies

Started over 7 years ago
by kamisen
Not Answered

services size is zero 0

sometime,i use android app to scan ble device,it will display "the device dose not has required services",the gatt.getServices.size is zero.why?

547 views

0 replies

Started over 7 years ago
by nowen
Not Answered
one wire library for nrf51822 keil 0

one wire library for nrf51822 keil for connected ds18b20 .
- nrf51822 keil one wire
760 views

0 replies

Started over 7 years ago
by morteza1994

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

Bluetooth low energy: Bluetooth Smart and the Nordic's Softdevices - Part 1 GAP Advertising

Hung Bui

This blog series was created as an attempt to fill in the gap between how Bluetooth Smart is defined in the spec and how you can use our APIs and event from our softdevice to do what defined in the spec…
- 10 Dec 2015
nRF5x: Current measurement guide: Introduction

Stian Røed Hafskjold

###Other relevant posts A concise guide to equipment setup, and how to use the development kit for current measurements can be found here: Measuring current with PCA10040 v0.9.0 A post that describes…
- 1 Dec 2015
nRF5x: General PCB design guidelines for nRF51 series

Petter Myhre

When designing a PCB with nRF51, nRF51822 or nRF51422, there are some rules that should be followed in order to get a good working radio/system, with a maximized range. General rule The RF part of the…
- 13 Nov 2015
Software Development Kit: nRF5 SDK Scheduler Tutorial

Einar Thorsrud

2019-02-08: Updated tutorial to cover nRF5 SDK version 15.2. Introduction Scope The following topics will be included in this tutorial: Configuration of the Scheduler library. Using the scheduler with…
- 9 Nov 2015
Bluetooth low energy: Bluetooth low energy central tutorial

Anders Strand

Scope Topics that will be covered include: Before we begin Necessary equipment and software Necessary prior knowledge Setting up the example projects Background theory Central and peripheral roles…
- 4 Nov 2015
Software Development Kit: nRF5 SDK Application Timer Tutorial

Einar Thorsrud

2018-11-23: Updated tutorial to cover SDK version 15.2. 2019-02-08: Improved example project (SDK 15.2) and updated instructions accordingly. Introduction Scope The following topics will be included in…
- 30 Oct 2015