Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Error setting sampling frequency on lsm6dso - nrf52833 0

Hi all, I am running the lsm6dso zephyr sample on my nrf52833 dev kit. I am unable to set the sampling frequency. I get this error after flashing: This is my overlay...
15 views

0 replies

Started 1 day ago
by ReginaA101
Not Answered
AIN to 8-bit accuracy to reduce the leakage current 0

I refer to and the answer answer given by AI referring me to you. I need the lithium battery only to about 8-bit accuracy to reduce the leakage current. Please provide...
17 views

0 replies

Started 1 day ago
by skvery
Not Answered
nrf5340 custom board non-simultaneous updates without external flash with sysbuild on ncs2.7.0+ 0

Hello! I was wondering if there is any advice from trying to get Non-simultaneous firmware updates using sysbuild with the following constraints: Must update both App...
22 views

0 replies

Started 1 day ago
by AlejandroM
Not Answered
Incorrect SPI reads and inconsistent behavior on nRF54L15-DK when communicating with external sensor (ADXL372) 0

I'm using NCS v2.9.0 and attempting to communicate with an ADXL372 IMU over SPI. Occasionally, the MCU successfully reads from the IMU and begins printing values. However...
- development
- software
- nRF54L15
- spi
- zephyr
21 views

0 replies

Started 1 day ago
by rbmarcus
Not Answered
SDK 2.9.0 undefined reference to `nrfx_gppi_channel_alloc' 0

I'm updating our nRF5340 firmware from SDK 2.4.2 to the SDK2.9.0. After few modifications, I was able to compile it using the SDK2.8.0. Now I'm trying to compile it with SDK...
23 views

0 replies

Started 1 day ago
by Leiser

Recent in Nordic blog

Building a BLE application step by step from scratch

Jocelyn Masserot

Hi all, I'm working on a blog explaining from scratch how to develop a BLE application with nRF518122 chip. Step by step, I explain the different aspects of the embedded system development in a GCC environment…
- 11 Feb 2016
Segger Embedded Studio blog post rev2 DEPRECATED

Michael Dietz

Depreceted see new blog post for new version of embedded studio here: https://devzone.nordicsemi.com/blogs/1032/segger-embedded-studio-a-cross-platform-ide-w-no-c/ #Introduction This post is an introductory…
- 4 Feb 2016
BLE-to-SB quadcopter bridge

Daniel Veilleux

[UPDATE (Feb 8, 2016): I have incorporated the feedback that I received from several link-layer wizards in Trondheim.] Last fall I purchased an inexpensive quadcopter that uses Nordic's ShockBurst (SB…
- 4 Feb 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019