Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Ble Mesh and advertising 0

Hi, What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board When i download the app,why doesnt advertising exist.i cant...
- advertising
- mesh
981 views

0 replies

Started over 8 years ago
by Oguz Emre
Not Answered
Library for NRF905 on Raspberry Pi 0

Hi all, Is there any stable library for NRF905 on Raspberry Pi? Thanks and Regards, Wonderful IOT
- nrf905 raspberry pi library
2565 views

0 replies

Started over 8 years ago
by Wonderful IOT
Not Answered

How to know the master is iOS or android? 0

How to know the master is iOS or Android when nRF51/52 is advertising or connected?

463 views

0 replies

Started over 8 years ago
by efengzu
Not Answered
Nrf5 IoT sdk Warning issue 0

hello i am using the Nrf52dk with Visualgdb. i try to run the example project (tcp/IP -> client). i am using the Nrf5 IoT sdk v0.9 Project complied successfully but i...
- nrf52
- iot
746 views

0 replies

Started over 8 years ago
by All4here
Not Answered

OpenOCD with nRF52 and Olimex debugger 0

I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...

2223 views

0 replies

Started over 8 years ago
by Tosa

Recent in Nordic blog

nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019