Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Can anyone explain ble event in Python? 0

Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...

843 views

0 replies

Started over 10 years ago
by Owlman
Not Answered

pstorage_store doesn't call callback 0

pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...

744 views

0 replies

Started over 10 years ago
by F
Not Answered

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11 0

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11. Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work. I think your library...

917 views

0 replies

Started over 10 years ago
by Chois
Not Answered

nRf24l01+ stand alone operation 0

In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...

1673 views

0 replies

Started over 10 years ago
by mikebuzz
Not Answered
IoT SDK How use ipv6_address_set / ipv6_address_remove API? 0

[Dev Env] nRF51 DK IoT SDK 0.8 IoT SoftDevice [Question] how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API. To...
737 views

0 replies

Started over 10 years ago
by cucu

Recent in the DevZone Blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016