Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11 0

Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11. Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work. I think your library...

746 views

0 replies

Started over 9 years ago
by Chois
Not Answered

nRf24l01+ stand alone operation 0

In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...

1404 views

0 replies

Started over 9 years ago
by mikebuzz
Not Answered
IoT SDK How use ipv6_address_set / ipv6_address_remove API? 0

[Dev Env] nRF51 DK IoT SDK 0.8 IoT SoftDevice [Question] how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API. To...
563 views

0 replies

Started over 9 years ago
by cucu
Not Answered

nRF51822 USB dongle help 0

Hi Guys, I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine. We also have a MCU RTOS Emulator based on Qemu,we...

1301 views

0 replies

Started over 9 years ago
by tommyhung
Not Answered
[iOS: pairing cancelled] BLE GAP disconnection no more handle since SDK 7.3.0 ? 0

Hello, I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
- nrf51822 pairing io
705 views

0 replies

Started over 9 years ago
by Sebastien

Recent in Nordic blog

Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015
Building kernel for RPi2 with bluetooth_6lowpan for Raspbian

Håkon Alseth

Building kernel for RPi2 with bluetooth_6lowpan In this guide, you will have two choices: Cross-compilation build Native build Choose the one that fits your needs. Cross-compilation is…
- 9 Apr 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019