Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SPI00 on the nRF54L15 cannot operate at 32 MHz. 0

I'm trying to run the 32 MHz SPI00 on the nRF54L15DK to communicate with the MX25R64 flash. However, the clock signal I'm measuring is limited to 8 MHz. Do you have any ideas...
3 views

0 replies

Started 3 minutes ago
by HauJohn
Not Answered
Zephyr CPU load module on nRF54L15 0

Hi, I think the CPU-Load subsystem in the sdk-nrf for Zephyr does not yet support the nRF54L15 as of v2.9.1 and current main since some devicetree-handles are hardcoded...
- software
- Evaluation
- nRF54L15
- zephyr
11 views

0 replies

Started 27 minutes ago
by rothmajs
Not Answered
Number of satellites and signal after a long time without GPS fix 0

Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
11 views

0 replies

Started 42 minutes ago
by GoncaloS
Not Answered
FCC & RED certificate - nRF52840_QFAA 0

Hello, Our product that we currently design is based on the nRF52840 QFAA and w e are looking to achieve FCC, CE and RED compliance. I would like to request any certificates...
17 views

0 replies

Started 52 minutes ago
by Avgerinos89
Not Answered
Sysbuild directory structure with MCU_BOOT and multiple nRF5340 build targets (dk and custom board) 0

I'm still trying to figure out sysbuild. I want to use sysbuild for a custom board and am trying to build a directory structure so I can flash my nrf5340DK and my custom board...
10 views

0 replies

Started 1 hour ago
by lcj

Recent in Nordic blog

Allowing debugger access to nRF5340

Daniel Veilleux

After an nRF5340 executes a power-on, brown-out, watchdog timer, or pin reset it is not automatically accessible to debug probes. This is true even if the nRF5340's memory is completely blank --i.e. no…
- 15 Jan 2021
Connected Home over IP: Sneak peek of early development on nRF52840

Lukasz Duda

This blog post provides step-by-step instruction on running Door Lock example from the CHIP repository. It demonstrates how with help of the mobile phone, commission accessory to the network using Bluetooth…
- 28 Dec 2020
FruityMesh v1.0 - connection-based open source BLE Mesh now available on Github

Marius Heil

Hello everyone, 5 years ago, FruityMesh was open sourced as the first connection-based Bluetooth Low Energy mesh network based on the nRF52 series. Now, after constant development at our Mway headquarter…
- 17 Dec 2020

Latest guides

Software: Using a custom Secure Partition Manager with your application

Heidi-Irene Harvey Sollie

One of the samples available in the nRF Connect SDK is the Secure Partition Manager, which is required to run applications in the nonsecure domain of the CPU. The sample uses the SPM library available in…
- 12 Feb 2020
Getting Started : nRF Connect SDK Bluetooth Low Energy tutorial part 1: Custom Service in Peripheral role

haakonsh

Scope The goal of this tutorial is to set-up your own custom Bluetooth Low Energy service on an nRF5340 acting in a peripheral role. We will set up a new Bluetooth LE project from scratch. The finished…
- 11 Feb 2020
Mesh Networks: Mass Provisioning of Nordic BLE Mesh Nodes

Mark Q

Purpose When creating a mesh network with many nodes, it can take a while to provision each node, especially using PyACI. An alternative is to use a static provisioner that provisions the nodes automatically…
- 8 Feb 2020
Software and Protocols: Enabling and testing TLS in mqtt_simple

Daniel Veilleux

The MQ Telemetry Transport (MQTT) protocol is hugely popular in IoT because it is lightweight and versatile. In this post we will enable Transport Layer Security (TLS) in the mqtt_simple sample from the…
- 4 Feb 2020
Getting Started: Introduction to Nordic nRF5 SDK and Softdevice

Mihua

What is the difference between SDK and Softdevice? How can we select SDK and Softdevice versions? Do the SoC, SDK, and Softdevice have version compatibility problems? How can we understand the SDK directory…
- 15 Jan 2020
Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020