Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
NCS 2.8.0: path length problem during build under Windows 0

Hello, I know that this issue comes up from time to time. I'm raising it again, because to my opinion there have to be a solution for this. Perhaps there is, that's the...
0 views

0 replies

Started 17 minutes ago
by rgrr2
Not Answered
Pin configurations for GPIO pins on NINA-B306-00B nRF52840 BLE module 0

Hello I’m using the NINA-B306-00B BLE module which uses the nRF52840 MCU for a custom board application. The BLE module interacts with two sensors, an accelerometer via SPI...
9 views

0 replies

Started 1 hour ago
by neeld
Not Answered
Correct way to integrate MQTT wifi sample into an existing project? 0

Hi, SDK: nRF Connect v2.7.0. Hardware: nrf5340 + nrf7002 module ( WT02C40C ) on a custom board. IDE: Visual Studio Code 1.95.3 (obviously with the nRF Connect extension...
11 views

0 replies

Started 1 hour ago
by __RICHARD__
Not Answered
Confirmation of nRF5340 CC312 Accelerator Usage and Power Consumption Analysis 0

1. When adding CONFIG_PSA_CRYPTO_DRIVER_CC3XX=y to the configuration as shown in the diagram, does it enable the use of the CC310 accelerator? 2. My understanding is...
21 views

0 replies

Started 5 hours ago
by giun.kim
Not Answered
Is it possible to configure a device as a standard BLE server and a PAwR node? Other PAwR limitations? 0

I am currently working on two separate sample repositories: one for a standard 1:1 BLE connection with a mobile phone and another for a PAwR node that transmits data alongside...
20 views

0 replies

Started 5 hours ago
by rbmarcus

Recent in Nordic blog

nRF BLINKY compatible firmware using Zephyr Bluetooth APIs

vikrant8051

Hello World !! This is simple code which is compatible for nRF Blinky App which is based on Zephyr OS Bluetooth APIs. I've tested it on #nRF52840-PDK board. Isn't it simple ? You have to just replace…
- 24 Jan 2018
How to interface a Nordic Thingy:52 using Amazon Alexa

gamnes

Interfacing the Nordic Thingy:52 from the Amazon Alexa Voice Service just had to be done! In this blog post I will briefly explain how this demo was set up, but I will direct you to the GitHub page if…
- 24 Jan 2018
Difference between nRF52840 Engineering A and B reference designs

MartinBL

After the release of nRF52840 Engineering B we have received several inquiries about the difference between Engineering A (nRF52840-QIAAAA) and Engineering B (nRF52840-QIAABB) reference designs. One reason…
- 15 Jan 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019