Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
GRTC resets after sys_poweroff when using MCUboot (ncs 3.1.0) 0

Hello Nordic team, We are using the GRTC on the nRF54L15 , and we are observing the following behavior: When MCUboot is enabled , the GRTC (likely backed by SYSCOUNTER...
23 views

0 replies

Started 4 hours ago
by ddiassword
Not Answered
AT Command Documentation for NTN Development on nRF9151-LACA-A1A-R (SLM Mode) 0

Hi everyone, I’m currently working with the nRF9151-LACA-A1A-R module, developing NTN communication features using SLM mode. However, I haven’t been able to find any documentation...
19 views

0 replies

Started 4 hours ago
by felipe.eaware
Not Answered
HTTP Client + W5500 on nRF5340: Works with IP but fails with domain names (DNS resolution fails) 0

Hi everyone, I’m trying to use the HTTP client sample from NCS v3.0.2 with a W5500 Ethernet shield on an nRF5340. DHCP works fine, and I can successfully POST and GET using...
8 views

0 replies

Started 8 hours ago
by Haris Iqbal
Not Answered
PPK II reliability and interaction with DC/DC converters 0

Hi, We've been using the PPK II for basically every IoT project we've carried out in the last few years, and it has been an incredibly useful tool. Our standard use case...
13 views

0 replies

Started 8 hours ago
by ecasado_iz
Not Answered
GPS CN0 Test 0

If you have tested the nRF9151's GPS with the CMW100 or IQ station. We need to know: 1. What test waveform file is required? 2. Should we use the ARB file or the CW waveform...
8 views

0 replies

Started 9 hours ago
by Bruce Chen

Recent in the DevZone Blog

Comparing compilers/IDEs for development with nRF5x series devices

Michael Dietz

#Introduction All compilers ARE NOT created equal. Given the same c code, different compilers will generate machine code with varying performance & size. Generally the more efficient machine code (uses…
- 28 Jan 2016
nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016