Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to see LOG_INF, LOG_WRN messages, preferably in real time 0

Al over these example programs there are all these messages like LOG_INF ( "Filters matched. Address: %s connectable: %d " , addr , connectable ); How do you actually...
0 views

0 replies

Started a few seconds ago
by DiBosco
Not Answered
nrfx_saadc advanced non-blocking sampling with internal timer example not working 0

Im trying to get SAADC to continuously sample using internal timer but im getting couple of samples and then it stops, tried everything but I'm obviously forgetting something...
4 views

0 replies

Started 4 minutes ago
by IvanR
Not Answered
nRF54L15 Multipoint 0

Hello, Does the nRF54L15 have multipoint? In my application, I would like to have different devices connected simultaneously, so I was looking for something like multipoint...
6 views

0 replies

Started 31 minutes ago
by Joao Rego
Not Answered
Assistance Needed: Power Profiler II Connection and Mode Selection for PCBA Testing 0

Dear Team, We want to use the Power Profiler II as our ammeter to measure the current of our newly designed PCBA. However, we’re uncertain about the proper connections for...
5 views

0 replies

Started 47 minutes ago
by Viknesh
Not Answered
Can not run nomally when setting CONFIG_BT_BONDABLE 0

I am running demo nrf/samples/matter/lock. I tried to use CHIP_NUS so I set CONFIG_CHIP_NUS =y, it worked well. After that, I wanted to make it bondable so I set CONFIG_BT_BONDABLE...
10 views

0 replies

Started 53 minutes ago
by Llama12580

Recent in Nordic blog

OLED display support for nRF52832 (SSD1306, Adafruit GFX)

Mahesh Venkitachalam

Just a quick post to say that we have ported the Adafruit GFX and SSD1306 libraries to nRF52832. Currently only I2C is supported. The code can be found here: https://github.com/electronut/ElectronutLabs…
- 11 Aug 2017
I tried 5 different debugger IDEs for nRF52 and STM32. Here are my results.

Jonathan

At Jumper we’re developing tools that increase the happiness levels of embedded software developers. Our main tool to date is the Jumper Emulator. As a part of the development process we’re required to…
- 9 Aug 2017
Things you should know about Bluetooth mesh

Eirik Midttun

Bluetooth SIG has recently published a new standard, the Bluetooth mesh. The mesh capability is a significant update and enables radical new applications. This in turn means that there are significant…
- 7 Aug 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019