Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Power Profiler Kit II ( Ampere Mode)-Measuring 300mA Current 0

I am trying to measure the 300mA system current. I cut off the system lane and connected Vin, Vout. And when in ampere mode, the system is not turning ON. (When I replaced...
24 views

0 replies

Started 6 hours ago
by HanyoungKang
Not Answered
Recover nRF5340 / MDBT53 after wrong DCDC config on LDO-only board 0

Hi Nordic, I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
27 views

0 replies

Started 6 hours ago
by Hejdern
Not Answered
ESB throughput drops when changing PRX TX power on nRF54L15 0

Hello Nordic support, I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
43 views

0 replies

Started 12 hours ago
by Ziyao Zhou
Not Answered
SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) 0

# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
113 views

0 replies

Started 2 days ago
by Sergei S
Not Answered
nRF52840 Output Power 0

A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
71 views

0 replies

Started 2 days ago
by Kevin01

Recent in the DevZone Blog

nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016