Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
If the nRESET is held low of nRF52840, would it shut it down? 0

Hi, What would be the state of SWD/SWCLK be when the nRF52840 is held in RESET mode? I am thinking if a simple gang programming be implemented by SWD/SWCLK be shared among...
12 views

0 replies

Started 4 hours ago
by kaushalyasat
Not Answered
Timing of retransmissions 0

Hi there, We are currently developing a system, where around 480 kbytes of data are transmitted over BLE. Throughput is supposed to be as high as possible. We are using...
14 views

0 replies

Started 6 hours ago
by JonasD27
Not Answered
VoIP support for nRF91x LTE Modules 0

Hello, Is there any documentation on setting up VoIP on the nRF91x module with Zephyr? As the nRF91x does not have a built-in VoIP app layer, I can assemble the hardware...
- nRF9160
- nRF Connect SDK
- Evaluation
- nRF9151
- zephyr
- hardware
14 views

0 replies

Started 8 hours ago
by 4HERE_Corp
Not Answered
Regulator fixed is broken in nrf sdk 3.2.1 0

After upgrading nRF Connect SDK from 3.1.1 to 3.2.1, our fixed regulator stopped working. We are on nRF54L15. Tracking it down further, this seems to be some sort of GPIO...
21 views

0 replies

Started 8 hours ago
by Konstantin Klitenik
Not Answered
Nordic Academy Cellular IoT Fundamentals Lesson 4 Exercise 2 (l4_e2): MQTT Connect error -111 even in the solution build 0

We are running some internal training on cellular, and it seems that Lesson 4, Exercise 2 is missing something (in the tab for NCS v3.2.0); the instructions to provide the...
8 views

0 replies

Started 9 hours ago
by Matteo Elimo

Recent in the DevZone Blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015