nrf52805: ADC polling mode issue

[Gokulnath]

Hardware setup: Custom board using BC805M-P (with App protect)
Software: nrf5 SDK S112 v17.0.2 ->Segger V7.30

My Objective: 

measure the Li-ion battery voltage(4.2V -100% till 3.6V-0%) through an external resistive divider & internal 0.6v ref voltage. (I'm not worried about the current consumption as of this moment. would like to make this concept work & all the other optimisations shall see later. Regarding optimisations yes I'm aware of this page: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/measuring-lithium-battery-voltage-with-nrf52)

What works so far?
for the moment my example measured voltage value is being transmitted over BLE through the battery service. it's all working well.
But the ADC is just measuring some garbage value (random) which is clearly not correct.

My concept of ADC polling mode is taken from this post & modified for my work. https://devzone.nordicsemi.com/f/nordic-q-a/14486/measuring-the-battery-voltage-with-nrf52832/129422

// Input range of External Vdd measurement = (0.6 V)/(1/5) = 3 V
// 3.0 volts ->  16383 ADC counts with 14-bit sampling:  5461 counts per volt
// 3.0 volts ->  4095 ADC counts with 12-bit sampling:  1365 counts per volt

#define ADC12_COUNTS_PER_VOLT 5461

void Adc12bitPolledInitialise(void)
{
    uint32_t timeout = 10;
    nrf_saadc_channel_config_t myConfig =
    {
        .resistor_p = NRF_SAADC_RESISTOR_DISABLED,
        .resistor_n = NRF_SAADC_RESISTOR_DISABLED,
        .gain       = NRF_SAADC_GAIN1_5,            // (1/5) Gain
        .reference  = NRF_SAADC_REFERENCE_INTERNAL, // 0.6V internal Ref Voltage
        .acq_time   = NRF_SAADC_ACQTIME_40US,       // See max source resistancetable
        .mode       = NRF_SAADC_MODE_SINGLE_ENDED,
        .burst      = NRF_SAADC_BURST_DISABLED,
        .pin_p      = NRF_SAADC_INPUT_AIN2,         // AIN2 for input Pin
        .pin_n      = NRF_SAADC_INPUT_DISABLED
    };

    nrf_saadc_resolution_set((nrf_saadc_resolution_t) 3);   // 2 is 12-bit , 3 for 14-bit 
    nrf_saadc_oversample_set((nrf_saadc_oversample_t) 2);   // 2 is 4x, about 150uSecs total
    nrf_saadc_int_disable(NRF_SAADC_INT_ALL);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_STARTED);
    nrf_saadc_enable();

    NRF_SAADC->CH[1].CONFIG =
              ((myConfig.resistor_p << SAADC_CH_CONFIG_RESP_Pos)   & SAADC_CH_CONFIG_RESP_Msk)
            | ((myConfig.resistor_n << SAADC_CH_CONFIG_RESN_Pos)   & SAADC_CH_CONFIG_RESN_Msk)
            | ((myConfig.gain       << SAADC_CH_CONFIG_GAIN_Pos)   & SAADC_CH_CONFIG_GAIN_Msk)
            | ((myConfig.reference  << SAADC_CH_CONFIG_REFSEL_Pos) & SAADC_CH_CONFIG_REFSEL_Msk)
            | ((myConfig.acq_time   << SAADC_CH_CONFIG_TACQ_Pos)   & SAADC_CH_CONFIG_TACQ_Msk)
            | ((myConfig.mode       << SAADC_CH_CONFIG_MODE_Pos)   & SAADC_CH_CONFIG_MODE_Msk)
            | ((myConfig.burst      << SAADC_CH_CONFIG_BURST_Pos)  & SAADC_CH_CONFIG_BURST_Msk);

    NRF_SAADC->CH[1].PSELN = myConfig.pin_n;
    NRF_SAADC->CH[1].PSELP = myConfig.pin_p;
}

void ble_Update_BatteryVoltage(void)
{
    // Enable command & Turn on the Power
    nrf_gpio_pin_write(ADC_SWITCH, 1); //turning on the voltage bridge on with a transistor
    nrf_saadc_enable();

    uint16_t result = 9999;         // Some recognisable dummy value
    uint32_t timeout = 100000;       // Trial and error
    volatile int16_t buffer[8];

    NRF_SAADC->RESULT.PTR = (uint32_t)buffer;
    NRF_SAADC->RESULT.MAXCNT = 1;

    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);
    nrf_saadc_task_trigger(NRF_SAADC_TASK_START);
    nrf_saadc_task_trigger(NRF_SAADC_TASK_SAMPLE);

    if (timeout != 0)
    {
        result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/
        5)) / ADC12_COUNTS_PER_VOLT;
    }

    while (0 == nrf_saadc_event_check(NRF_SAADC_EVENT_END) && timeout > 0)
    {
        timeout--;
    }
    nrf_saadc_task_trigger(NRF_SAADC_TASK_STOP);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_STARTED);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);

    // Disable command & turn off the Power to ADC Bridge to reduce power consumption
    nrf_saadc_disable();
    
    nrf_gpio_pin_write(ADC_SWITCH, 0); //turning off the voltage bridge on with a transistor
    ble_bas_battery_level_update(&m_bas, result, m_conn_handle); 
}

The ADC result value is clearly not accurately working when I'm just calling the function manually upon a button press. ble_Update_BatteryVoltage();

What am I doing wrong?

Thanks, for any valuable input I'm new to NRF. 
Gokunath 

[helsing]

Hi Gokulnath,

My Objective: 

measure the Li-ion battery voltage(4.2V -100% till 3.6V-0%) through an external resistive divider & internal 0.6v ref voltage. (I'm not worried about the current consumption as of this moment. would like to make this concept work & all the other optimisations shall see later

You could try the peripheral/saadc sample in nRF5 SDK.

But the ADC is just measuring some garbage value (random) which is clearly not correct.

What does this look like? Would you be able to provide an example? Does the this change if you change the voltage?

Thanks, for any valuable input I'm new to NRF. 

nRF Connect SDK is recommended for new designs. Please see the nRF Connect SDK and nRF5 SDK statement as well as the nRF Connect SDK Fundamentals course at Nordic Developer Academy.

https://www.nordicsemi.com/Products/Development-software/nrf-connect-sdk

Here are some samples for nRF Connect SDK. You could start with simple_blocking or simple_nonblocking: hal_nordic/nrfx/samples/src/nrfx_saadc at master · zephyrproject-rtos/hal_nordic · GitHub

[hmolesworth]

There is a bug here, the result is read before the SAADC sample has completed:

    if (timeout != 0)
    {
        result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/
        5)) / ADC12_COUNTS_PER_VOLT;
    }

    while (0 == nrf_saadc_event_check(NRF_SAADC_EVENT_END) && timeout > 0)
    {
        timeout--;
    }

Change to:

    while (0 == nrf_saadc_event_check(NRF_SAADC_EVENT_END) && timeout > 0)
    {
        timeout--;
    }
    if (timeout != 0)
    {
        result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/
        5)) / ADC12_COUNTS_PER_VOLT;
    }

[Gokulnath]

Hi hmolesworth  helsing 

I've noticed in debugging that my averaging might not be correct due to that I suspect it's moving a lot. 

can you please verify it,

    if (timeout != 0)
    {
        result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/
        5)) / ADC12_COUNTS_PER_VOLT;
    }

 especially this line? 


EDIT:
sorry there was my typo during copy pasting the code in this thread. my correct code is still this.

result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/2)) / ADC12_COUNTS_PER_VOLT;


Thanks,
Gokulnath A R

[helsing]

Hi Gokulnath, sorry for the delay.

Some context is missing. However, it looks like you are performing many steps in only a few lines. Why not break up the calculations and print out the intermediate values? That way you could confirm that you are performing the intended calculations.

[hmolesworth]

There is a typo in this line, which was correct in your earlier post. Also note that this is not averaging, it is rounding; this means the averaging is presumably performed in ble_bas_battery_level_update()

// This line rounds the reading
Change
    result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/5)) / ADC12_COUNTS_PER_VOLT;
To
    result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/2)) / ADC12_COUNTS_PER_VOLT;

You can add the averaging I posted earlier, something like this:

void LowPassFilter(uint16_t *FilteredValue, result);

// Measured battery voltage - filtered value
static uint16_t MeasuredBatteryVoltage = 0;

    if (timeout != 0)
    {
        result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/2)) / ADC12_COUNTS_PER_VOLT;
        LowPassFilter(&MeasuredBatteryVoltage, result);
        // Use filtered value instead of raw sample
        result = MeasuredBatteryVoltage;
    }
.. snip ..
    ble_bas_battery_level_update(&m_bas, result, m_conn_handle); 

    return result;

Edit: If using the circuit first posted,  the numbers in the log don't look correct:

Vadc = Vbat*300/(120+300) = (Vbat*300)/420
Vadc411 = 2936 mV
Vadc368 = 2629 mV

// Input range of internal Vdd measurement = (0.6 V)/(1/5) = 3 V
// 3.0 volts ->  16383 ADC counts with 14-bit sampling:  5461 counts per volt
// 3.0 volts ->   4095 ADC counts with 14-bit sampling:  1365 counts per volt
Vadc411 = 2936 mV = 16033 counts with 14-bit sampling
Vadc411 = 2936 mV =  4007 counts with 12-bit sampling

result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/2)) / ADC12_COUNTS_PER_VOLT;
result411 = ((16033 * 1000)+(5461/2))/5461 = 2936 with 14-bit sampling
result411 = (( 4007 * 1000)+(1365/2))/1365 = 2936 with 12-bit sampling
Vbat = 2936 * (120+300)/300 = 4110 mV = 4.11 V

From the log:
Voltage on BLE // 4.11V on voltage divider input from a Bench Power supply.
I      0BLEParserBase.CopyToRawData:Data:0x76  <<== 118, should be 0x678 for 14-bit, 0x555 for 12-bit

Maybe explicitly cast to uint32_t to ensure 32-bit processing:

// Ensure 32-bit processing:
result = (uint16_t)(((uint32_t)buffer[0] * 1000UL)+((uint32_t)ADC12_COUNTS_PER_VOLT/2)) / (uint32_t)ADC12_COUNTS_PER_VOLT);

Helsing's suggestion of printing out intermediate steps is the best way to verify the code is doing what you expect.

[Gokulnath]

Hey,

Sorry for my delay in updating this thread with my hardware changes.

Just an update I've updated the custom PCB to this & This would be my current most updated hardware setting.

I haven't implemented your filter on the software yet.

With this current configuration (2 versions of Custom PCB), I have an oscillation delta of +-8% in both versions PCB from the true battery charge %.

(Just incase I've shunted the Transistor too(For Testing purposes) to see if it makes any change in output BUT the result remains the same)

In Both Versions of PCB the ADC Voltage Divider Ratio is the same.

Version 1 with ADC Switch PCB Below: 
 

Version 2 without Transistor Switch PCB Below:

 

In Both Versions of the PCB I've added Ferrite Beads for EMC stability like shown below (Ofc Version 2 PCB doesn't have ADC switch input like shown below.)



My current ADC input is AIN3.

My Desired Battery voltage range is this: 4.2V 100% => 3.63V 0%

I explicitly add a software delay to make the capacitor charge too to avoid any inconsistencies in the hardware voltage level.

my latest adc code is below:

void Adc12bitPolledInitialise(void)
{
    uint32_t timeout = 10;
    nrf_saadc_channel_config_t myConfig =
    {
        .resistor_p = NRF_SAADC_RESISTOR_DISABLED,
        .resistor_n = NRF_SAADC_RESISTOR_DISABLED,
        .gain       = NRF_SAADC_GAIN1_5,            // (1/5) Gain
        .reference  = NRF_SAADC_REFERENCE_INTERNAL, // 0.6V internal Ref Voltage
        .acq_time   = NRF_SAADC_ACQTIME_40US,       // See max source resistancetable
        .mode       = NRF_SAADC_MODE_SINGLE_ENDED,
        .burst      = NRF_SAADC_BURST_DISABLED,
        .pin_p      = NRF_SAADC_INPUT_AIN3,         // AIN3 for input Pin
        .pin_n      = NRF_SAADC_INPUT_DISABLED
    };

    nrf_saadc_resolution_set((nrf_saadc_resolution_t) 3);   // 2 is 12-bit , 3 for 14-bit 
    //nrf_saadc_oversample_set((nrf_saadc_oversample_t) 2);   // 2 is 4x, about 150uSecs total
    nrf_saadc_int_disable(NRF_SAADC_INT_ALL);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_STARTED);
    nrf_saadc_enable();

    NRF_SAADC->CH[1].CONFIG =
              ((myConfig.resistor_p << SAADC_CH_CONFIG_RESP_Pos)   & SAADC_CH_CONFIG_RESP_Msk)
            | ((myConfig.resistor_n << SAADC_CH_CONFIG_RESN_Pos)   & SAADC_CH_CONFIG_RESN_Msk)
            | ((myConfig.gain       << SAADC_CH_CONFIG_GAIN_Pos)   & SAADC_CH_CONFIG_GAIN_Msk)
            | ((myConfig.reference  << SAADC_CH_CONFIG_REFSEL_Pos) & SAADC_CH_CONFIG_REFSEL_Msk)
            | ((myConfig.acq_time   << SAADC_CH_CONFIG_TACQ_Pos)   & SAADC_CH_CONFIG_TACQ_Msk)
            | ((myConfig.mode       << SAADC_CH_CONFIG_MODE_Pos)   & SAADC_CH_CONFIG_MODE_Msk)
            | ((myConfig.burst      << SAADC_CH_CONFIG_BURST_Pos)  & SAADC_CH_CONFIG_BURST_Msk);

    NRF_SAADC->CH[1].PSELN = myConfig.pin_n;
    NRF_SAADC->CH[1].PSELP = myConfig.pin_p;
    nrf_gpio_pin_write(ADC_SWITCH, 1); //Turning on  the voltage divider with a transistor
}

void ble_Update_BatteryVoltage(void)
{
    // Enable command & Turn on the Power
    nrf_gpio_pin_write(ADC_SWITCH, 1); //Turning on  the voltage divider with a transistor
    nrf_saadc_enable();

    nrf_delay_ms(100); // add a delay to make the capacitor charge 

    uint16_t result = 0;              // Some recognisable dummy value
    uint32_t timeout = 1000000;       // Trial and error
    volatile int32_t buffer[20];

    NRF_SAADC->RESULT.PTR = (uint32_t)buffer;
    NRF_SAADC->RESULT.MAXCNT = 1;

    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);
    nrf_saadc_task_trigger(NRF_SAADC_TASK_START);
    nrf_saadc_task_trigger(NRF_SAADC_TASK_SAMPLE);

    while (0 == nrf_saadc_event_check(NRF_SAADC_EVENT_END) && timeout > 0)
    {
        timeout--;
    }

    if (timeout != 0)
    {
        result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/2)) / ADC12_COUNTS_PER_VOLT;
        result += 5;
    }

    // Disable command & turn off the Power to ADC Bridge to reduce power consumption
    nrf_gpio_pin_write(ADC_SWITCH, 0); //Turning off the voltage divider transistor
    nrf_saadc_disable();

    nrf_saadc_task_trigger(NRF_SAADC_TASK_STOP);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_STARTED);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);
    
    while(result>100 && result >0)
    {
    result = result%100;
    }
    
    if(Old_Bat != result && result >=1 && result !=0)
    {

    if(result<=17)
    {
    result = 5;
    nrf_gpio_pin_write(BLUE_LED, 0); //Turning on the LOW BAttery Flash LED
    nrf_delay_ms(1000); // add a delay to make the capacitor charge 
    nrf_gpio_pin_write(BLUE_LED, 1); //Turning off the LOW BAttery Flash LED   
    }
    
    Old_Bat = result;
    ble_bas_battery_level_update(&m_bas, result, m_conn_handle);
    }
    
}

Since I thought there was a fundamental problem with my code/hardware configuration I didn't add the software filter yet. 

if there seems to be no fundamental error on this config I shall proceed to add the software filter which you guys suggested.

In this above code, I've just added some phantom code to round off the results + some offset so that the result always comes between 0-100% on BLE.

especially here below: 

while(result>100 && result >0)
    {
    result = result%100;
    }
    
    if(Old_Bat != result && result >=1 && result !=0)
    {

    if(result<=17)
    {
    result = 5;

P.S. If you need a log for this setup I can provide you with one. (the previous log in this forum thread is not from this latest setup)

Thanks in advance,
Gokulnath A R

[helsing]

Hi Gokulnath, sorry for the long delay.

What are the reslults from your lateste updated code?

Anyways, looking over this thread, somthing that seems to be missing is the wait for the SAADC to be ready, by checking for the NRF_SAADC_EVENT_STARTED event. By adding a check for the NRF_SAADC_EVENT_STARTED event before initiating sampling, you can ensure that the ADC has fully powered up and stabilized:

// Start the SAADC to prepare for sampling
nrf_saadc_task_trigger(NRF_SAADC_TASK_START);

// Wait until the SAADC is ready (EVENT_STARTED is set)
while (!nrf_saadc_event_check(NRF_SAADC_EVENT_STARTED)) {
    // Optionally, you could add a timeout mechanism here to avoid waiting indefinitely
}

// Clear the STARTED event to enable detection next time
nrf_saadc_event_clear(NRF_SAADC_EVENT_STARTED);

// Trigger the SAADC to take a sample now that it is ready
nrf_saadc_task_trigger(NRF_SAADC_TASK_SAMPLE);

[Gokulnath]

Hey helsing ,
Thanks for the suggestion I've also added the calibration too..

my new code below along with my New Hardware. But i have a few questions so asked them below (next thread) 

// Input range of internal Vdd measurement = (0.6 V)/(1) = 0.6 V MAX in External Resistor Divider Output.
// 16384 ADC counts with 14-bit sampling:  0.1v = 2730.6 ADC Counts
// Resistor Divider 2.2M & 360K
// 4.2V  => 0.591 volts -> Assuming 100% Battery SoC
// 3.63V => 0.51 Volts -> Assuming 0% Battery SoC
//  Vadc= Vbat * ((360K)/(360K+2M2)) => Vadc = Vbat * 0.140625

void Adc12bitPolledInitialise(void)
{
    uint32_t timeout = 10;
    nrf_saadc_channel_config_t myConfig =
    {
        .resistor_p = NRF_SAADC_RESISTOR_DISABLED,
        .resistor_n = NRF_SAADC_RESISTOR_DISABLED,
        .gain       = NRF_SAADC_GAIN1,              //  1 Gain
        .reference  = NRF_SAADC_REFERENCE_INTERNAL, // 0.6V internal Ref Voltage
        .acq_time   = NRF_SAADC_ACQTIME_40US,       // See max source resistancetable
        .mode       = NRF_SAADC_MODE_SINGLE_ENDED,
        .burst      = NRF_SAADC_BURST_DISABLED,
        .pin_p      = NRF_SAADC_INPUT_AIN3,         // AIN3 for input Pin
        .pin_n      = NRF_SAADC_INPUT_DISABLED
    };

    nrf_saadc_resolution_set((nrf_saadc_resolution_t) 3);   // 2 is 12-bit , 3 for 14-bit 
    //nrf_saadc_oversample_set((nrf_saadc_oversample_t) 2);   // 2 is 4x, about 150uSecs total
    nrf_saadc_int_disable(NRF_SAADC_INT_ALL);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_STARTED);
    nrf_saadc_enable();

    NRF_SAADC->CH[1].CONFIG =
              ((myConfig.resistor_p << SAADC_CH_CONFIG_RESP_Pos)   & SAADC_CH_CONFIG_RESP_Msk)
            | ((myConfig.resistor_n << SAADC_CH_CONFIG_RESN_Pos)   & SAADC_CH_CONFIG_RESN_Msk)
            | ((myConfig.gain       << SAADC_CH_CONFIG_GAIN_Pos)   & SAADC_CH_CONFIG_GAIN_Msk)
            | ((myConfig.reference  << SAADC_CH_CONFIG_REFSEL_Pos) & SAADC_CH_CONFIG_REFSEL_Msk)
            | ((myConfig.acq_time   << SAADC_CH_CONFIG_TACQ_Pos)   & SAADC_CH_CONFIG_TACQ_Msk)
            | ((myConfig.mode       << SAADC_CH_CONFIG_MODE_Pos)   & SAADC_CH_CONFIG_MODE_Msk)
            | ((myConfig.burst      << SAADC_CH_CONFIG_BURST_Pos)  & SAADC_CH_CONFIG_BURST_Msk);

    NRF_SAADC->CH[1].PSELN = myConfig.pin_n;
    NRF_SAADC->CH[1].PSELP = myConfig.pin_p;
}

void ble_Update_BatteryVoltage(void)
{
    nrf_saadc_enable();

    nrf_delay_ms(100); // add a delay to make the capacitor charge 

    volatile float result = 0;              // Some recognisable dummy value
    uint32_t timeout = 1000000;       // Trial and error
    volatile int32_t buffer[10];

    NRF_SAADC->RESULT.PTR = (uint32_t)buffer;
    NRF_SAADC->RESULT.MAXCNT = 1;

    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);
    nrf_saadc_task_trigger(NRF_SAADC_TASK_START);   // Start the SAADC to prepare for sampling

    // Wait until the SAADC is ready (EVENT_STARTED is set)
    while (!nrf_saadc_event_check(NRF_SAADC_EVENT_STARTED) && !nrf_saadc_event_check(NRF_SAADC_EVENT_CALIBRATEDONE)) 
    {
        // Optionally, you could add a timeout mechanism here to avoid waiting indefinitely
    }

    nrf_saadc_task_trigger(NRF_SAADC_TASK_SAMPLE);  // Trigger the SAADC to take a sample now that it is ready

    while (0 == nrf_saadc_event_check(NRF_SAADC_EVENT_END) && timeout > 0)
    {
        timeout--;
    }

    if (timeout != 0)
    {
        //result = ((buffer[0] * 1000L)+(ADC12_COUNTS_PER_VOLT/2)) / ADC12_COUNTS_PER_VOLT;
        result = (float)((buffer[0] * 1000L) * 1.667 * 16384);
        result = result/0.140625;
        result = volttopercent(result);
    }

    nrf_saadc_disable();

    nrf_saadc_task_trigger(NRF_SAADC_TASK_STOP);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_STARTED);  // Clear the STARTED event to enable detection next time
    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);
    
    /*
    while(result>100 && result >0)
    {
    result = result%100;
    }
    */
         
    if(Old_Bat != result && result >=1 && result !=0)
    {

    if(result<=5)
    {
    //result = 5;
    nrf_gpio_pin_write(BLUE_LED, 0); //Turning on the LOW BAttery Flash LED
    nrf_delay_ms(1000); // add a delay to make the capacitor charge 
    nrf_gpio_pin_write(BLUE_LED, 1); //Turning off the LOW BAttery Flash LED   
    }
    
    Old_Bat = result;
    ble_bas_battery_level_update(&m_bas, result, m_conn_handle);
    }
    nrf_saadc_task_trigger(NRF_SAADC_TASK_CALIBRATEOFFSET);
}

float volttopercent(float vadc)
{
  float Vmax = 4.2;
  float Vmin = 3.63;
  
  float percentage;

  percentage = ((vadc -Vmin)/(Vmax - Vmin))*100;

  return percentage;
}

I'm still testing it so dont know the results 100% yet.
Thanks 

[hmolesworth]

Using the code posted with the floating-point percentage calculation: This data comes from your code using a 2.996 volt input (slightly different resistors, but that is not the point here):

-Raw SAADC-   --------Scaled-------   --------Percent1-----    -------Percent2-----
 Dec   Hex     Decimal     Hex         Decimal      Hex         Decimal      Hex
==== ======   ========== ==========   ========== ==========    ========== ==========
2979 0x0BA3    2979.00   0x453A3000      39.86  0x421F6DB7       39.86 0x421F6DB7
2972 0x0B9C    2972.00   0x4539C000      38.86  0x421B6DB7       38.86 0x421B6DB7
2965 0x0B95    2965.00   0x45395000      37.86  0x42176DB7       37.86 0x42176DB7
2964 0x0B94    2964.00   0x45394000      37.71  0x4216DB6D       37.71 0x4216DB6D
2966 0x0B96    2966.00   0x45396000      38.00  0x42180000       38.00 0x42180000
2966 0x0B96    2966.00   0x45396000      38.00  0x42180000       38.00 0x42180000
with Burst 4 enabled
2981 0x0BA5    2981.00   0x453A5000      40.14  0x42209249       40.14 0x42209249
2970 0x0B9A    2970.00   0x4539A000      38.57  0x421A4925       38.57 0x421A4925
2972 0x0B9C    2972.00   0x4539C000      38.86  0x421B6DB7       38.86 0x421B6DB7
2965 0x0B95    2965.00   0x45395000      37.86  0x42176DB7       37.86 0x42176DB7
2966 0x0B96    2966.00   0x45396000      38.00  0x42180000       38.00 0x42180000
2966 0x0B96    2966.00   0x45396000      38.00  0x42180000       38.00 0x42180000

ints truncate floats; also as an aside floats (on the nRF52 hardware) are only 32-bit inclusive of sign and exponent, so have less precision than 32-bit ints. Compiler implicit conversion is compiler-dependent.

The data above is generated by adding these lines to the code :

// Input range = (0.6 V)/(1)   = 0.6V -> 3.393 V with 931k/200K dividers
// 3.0 volts -> 14486 ADC counts with 14-bit sampling: 4828.8 counts per volt
#define ADC12_COUNTS_PER_VOLT 4829

    // Disable command & turn off the Power to ADC Bridge to reduce power consumption
    nrf_gpio_pin_write(ADC_SWITCH, 0); //Turning off the voltage divider transistor
    nrf_saadc_disable();
    nrf_saadc_task_trigger(NRF_SAADC_TASK_STOP);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_STARTED);
    nrf_saadc_event_clear(NRF_SAADC_EVENT_END);
    float f_result = (float)((buffer[0] * 1000L) * 1.667 * 16384);
    f_result = result; ///0.140625;
    int32_t i_result = result; ///0.140625;
    float percent_result1 = volttopercent(i_result);
    float percent_result2 = volttopercent(f_result);
    char InfoPacket[180] = "";
    // -Raw SAADC-   -------Scaled-----   ------Percent1----   ------Percent2----
    //  Dec   Hex    Decimal   Hex        Decimal     Hex      Decimal    Hex
    // ==== ======   ======= ==========   ======= ==========   ======= ==========
    // 2968 0x0B98   2968.00 0x45398000     38.29 0x42192492     38.29 0x42192492
    snprintf(InfoPacket, sizeof(InfoPacket), "-Raw SAADC-   -------Scaled-----   ------Percent1----   ------Percent2----\r\n");  uartSend(InfoPacket, strlen(InfoPacket));
    snprintf(InfoPacket, sizeof(InfoPacket), " Dec   Hex    Decimal   Hex        Decimal     Hex      Decimal    Hex\r\n");     uartSend(InfoPacket, strlen(InfoPacket));
    snprintf(InfoPacket, sizeof(InfoPacket), "==== ======   ======= ==========   ======= ==========   ======= ==========\r\n"); uartSend(InfoPacket, strlen(InfoPacket));
    snprintf(InfoPacket, sizeof(InfoPacket), "%4d 0x%04X  %8.2f 0x%08X    %6.2f 0x%08X    %6.2f 0x%08X\r\n", result, result, f_result, *(uint32_t *)&f_result, percent_result1, *(uint32_t *)&percent_result1, percent_result2, *(uint32_t *)&percent_result2);
    uartSend(InfoPacket, strlen(InfoPacket));

My post here is to show how to check the algorithm is doing the required actions ..

Edit: I commented out the peculiar 0.140625 divider, correctd the hex float print and changed the % calc to use mV and correct min & max for my test setup

[hmolesworth]

I corrected the hex float print and changed the % calculation to use mV and correct min & max for my test setup with 2032 coin cell

float volttopercent(float vadc)
{
  float Vmax = 3400; // mV was 4.2;
  float Vmin = 2700; // mV was3.63;
  float percentage;
  percentage = ((vadc -Vmin)/(Vmax - Vmin))*100;
  return percentage;
}

Results look more sensible:

-Raw SAADC-   ------Scaled------   ------Percent1----   -----Percent2------
 Dec   Hex    Decimal   Hex        Decimal   Hex        Decimal      Hex
==== ======   ======= ==========   ======= ==========   =======  ==========
2979 0x0BA3   2979.00 0x453A3000     39.86 0x421F6DB7     39.86  0x421F6DB7