nRF5340 Missing Disconnect Event (Supervision Timeout)

[JeffW]

Hi,

I have a nRF5340 using hci_ipc that has the following features:

• Central Role + Scanning (Multi-connection to nRF52840 peripherals)
• Peripheral Role
• QoS Channel Scanning
• Nordic Uart (Server + Client)
  
  

I am missing bluetooth supervision timeout events with the nRF53 with both ncs 2.7.0 and the upstream Zephyr BLE stack. (No disconnected callback using the Softdevice).

Problem Flow from Central perspective:
1) Scan and connect
2) Subscribe to NUS (cached handles - no discovery)
3) MTU Exchange
4) Send NUS data back and forth (~1.2Kb DTLS handshake)
5) Disconnect Peripheral with pending Central NUS GATT write (breakpoint peripheral nrf52 / power off / reset)
6) Observe no supervision timeout (4s) [This event expected, but doesn't happen]
7) Observe GATT write error 30s later
8) GATT error cleans up nus subscription, manually issue disconnect here
9) Observe no .disconnected callback

Setups used:

1) Initially we were on NCS 2.7.0 with the included hci_ipc using the ipc_radio sample with a few upstream network (not bluetooth) related cherrypicks. We had problems with this configuration missing disconnect events.
2) Now we're on a heavily cherrypicked SDK to get as close to Zephyr main upstream Bluetooth stack (from the last couple days) & the newest nrfx-lib softdevice+hci_ipc. We still had problems with this.
3) With the heavily cherrypicked SDK, we enabled SPLIT_SW_LL and do not miss these supervision timeout events with the same application code.

I am curious what layer these disconnect events are supposed to get propagated through `zephyr/drivers/bluetooth/ipc/ipc.c` when using `hci_ipc`.

I have not yet been able to make a minimum viable example, but am working towards this.

I made a Zephyr discord post regarding this on #nordic for additional context, which I tried to summarize here.
https://discord.com/channels/720317445772017664/883445320812466209/1283513590606860318

Let me know if I can provide additional information,
Jeff

[Vidar Berg]

Hi Jeff,

Thank you for the detailed summary of your setup. This helped me create minimal peripheral and central projects based on our peripheral and central UART, allowing me to reproduce the issue within a couple of minutes (GATT timeout followed by a missed disconnect event). I have handed over the projects to our Bluetooth team for further investigation. Regarding the Zephyr controller, it uses two RX threads with one high priority thread, which may unblock the host. I will keep you updated on the progress.

Thank you,

Vidar

[JeffW]

Vidar,

That's great news!
Is it possible to share the sample projects? (No need to spend time cleaning up code)

We're more than happy to test and debug any potential solutions as this is our biggest blocker for customer sampling.

Very much appreciate the help,
--Jeff

[JeffW]

Vidar,

I appreciate the suggestions, but both the central and peripheral are multi-connection. Unfortunately due to this topology, just because the peripheral is advertising again does not mean that the central missed a disconnect event.

The connection pointer needs to have the correct state. I don't know how the supervision timeout does not get processed when almost nothing besides scanning is happening.

For the time being we're using the Split LL again, but ideally we move back to Nordic for a more familiar path to SIG certification.

--Jeff

[Vidar Berg]

Jeff,

It is surprising that this occurs when almost nothing is happening besides scanning. The issues we found earlier would only occur during high BLE activity. I have reported this as new issue internally. I also found out that we already include tests that simulate sudden disconnects by resetting the peer device. However, it seems we are not able to replicate the same conditions seen with your application.

Vidar

[JeffW]

Vidar,

My colleague was able to create a barebones sample to demonstrate this missing disconnect.

We modified your sample in these ways-
Peripheral:
On send enabled (this is after MTU update), we send 1000 bytes of zeros.
Central responds with 1000 bytes of ones. 
Repeats sending ones/twos/threes.
After we receive the last packet, we update the connection interval parameters and go idle.

Central:
Switch to IPC_RADIO
No auto connect on filter match
Vendor specific connection event report is enabled
Scanning is only disabled while connecting (code in main.c does not support multiple connections, but it is modeled after our application)

Inside the zip is a readme. 
Central was a nRF5340dk
Peripheral was a nRF52840dk


MissingDisconnectModifiedSamples.zip

[00:00:23.747,192] <dbg> bt_conn: tx_notify_process: conn 0x200018c8
[00:00:23.747,222] <dbg> bt_conn: tx_notify_process: tx 0x2000297c cb 0 user_data 0
[00:00:23.747,222] <dbg> bt_conn: tx_free: 0x2000297c

-- NOT ORIGINAL LOG --
-- BEGIN WINDOW WHERE I TURN OFF POWER TO 52840DK PERIPHERAL --

[00:00:23.747,253] <dbg> bt_conn: tx_notify_process: raise TX IRQ
[00:00:23.747,283] <dbg> bt_conn: bt_conn_tx_processor: start
[00:00:23.747,283] <dbg> bt_conn: bt_conn_tx_processor: no connection wants to do stuff
[00:00:24.047,241] <dbg> bt_conn: bt_conn_ref: handle 10 ref 2 -> 3
[00:00:24.047,271] <dbg> bt_conn: bt_conn_unref: handle 10 ref 3 -> 2

-- NOT ORIGINAL LOG --
-- END WINDOW --
-- IF DISCONNECTED, TURN ON AND TRY AGAIN, VARY WHEN POWER IS TURNED OFF IN THIS WINDOW --
-- IF UNABLE TO REPRODUCE, TRY SLIGHTLY BEFORE OR AFTER WINDOW--

[00:09:06.285,400] <inf> central_uart: Filters matched. Address: D4:BC:F8:83:7F:87 (random) connectable: 1
[00:09:06.285,583] <dbg> bt_conn: bt_conn_tx_processor: start
[00:09:06.285,583] <dbg> bt_conn: bt_conn_tx_processor: no connection wants to do stuff
[00:09:06.289,550] <dbg> bt_conn: bt_conn_ref: handle 10 ref 2 -> 3
[00:09:06.289,672] <wrn> bt_conn: Found valid connection (0x200018c8) with address D4:BC:F8:83:7F:87 (random) in connected state 
[00:09:06.289,672] <dbg> bt_conn: bt_conn_unref: handle 10 ref 3 -> 2
[00:09:06.289,703] <dbg> bt_conn: conn_le_create_common_checks: Conn check failed: ACL connection already exists.
[00:09:06.289,703] <err> central_uart: bt_conn_le_create failed (err -22)

--Jeff

[Vidar Berg]

Jeff, 

Thank you very much for creating this sample. We will use it to reproduce the issue on our end and hope to identify the root cause soon.

Vidar

[JeffW]

Hey Vidar,
 
Not expecting any solutions -- just curious if any teams were able to reproduce the problem given the sample, or not yet. :)

--Jeff