ble_app_hrs + Buttonless DFU on NRF52DK(52832) + OTA update

[Vick_Chang]

Hi,

I want to verify

1. Program  ble_app_hrs with buttonless dfu integrated + secure bootloader + bootloader setting to nRF52DK. 

2. Boot up nRF52DK, then use buttonless dfu goto bootloader mode

3. Update app_dfu_package.zip (nrfutil pkg generate --hw-version 52 --application-version 0 --application ble_ap nrfutil pkg generate --hw-version 52 --application-version 0 --application ble_app_hrs_pca10040_s132.hex --sd-req 0xCB --key-file private.key app_dfu_package.zip
Zip created at app_dfu_package.zip)

====

Below are my steps:

Step1 Generate bootloader setting page

Step2  merge secure bootloader(\dfu\secure_bootloader\pca10040_s132_ble\) + bootloader settings

Step3 Program secure bootloader (examples\dfu\secure_bootloader\pca10040_s132_ble)+ bl setting

Step4 Program softdevice (s132_nrf52_7.0.1)

Step5 Program app(ble_app_hrs_pca10040_s132 which is integrate with buttonless_duf already)

Step 6 When nRF52DK bootup, error logs are below:

Are my steps correct?

How can I make it right?

Thanks.

Vick

[sudharsan]

Hi, 

Please check on the below blog

https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/getting-started-with-nordics-secure-dfu-bootloader

Regards

Sudharsan

[Vick_Chang]

Hi Sudharsan,

I have followed the blog, and try below steps:

1. 

 In sdk_config.h in the bootloader:

• Change NRF_DFU_BLE_REQUIRES_BONDS to 1
• Change NRF_SDH_BLE_SERVICE_CHANGED to 1

- In sdk_config.h in ble_app_buttonless_dfu + ble_app_hrs

• Change NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS to 1
• Check if NRF_SDH_BLE_SERVICE_CHANGED is not 1 then set it to 1

Compile the two projects. 

2. Generate bl setting

3.

mergehex -m bootloader.hex setting.hex -o bootloader_and_setting.hex

4.

mergehex -m nrf52832_xxaa.hex bootloader_and_setting.hex -o app_bootloader_and_setting.hex

5. flash softdevice

6.  flash the app_bootloader_and_setting.hex

7. After bootup, error logs show below:

Could you give me a hand?

By the way, I have tested sec_bootloader + ble_app_hrs(without buttonless_dfu), the result is following.

When nRF52DK boots up, it will enter bootloader mode directly.  Is that normal?

(This verification just make sure the bootloader is available.)

Thanks you!

[Hung Bui]

Have you tried with --bl-settings-version 2 ? 

Please let me know which IDE you are using for compiling ? Usually you set the optimization and pre-processor symbols inside project setting. 

[Vick_Chang]

Hi Hung,

Have you tried with --bl-settings-version 2 ? 

=> Yes

IDE: SEGGER Embedded Studio

[sudharsan]

Vick_Chang said:

So below is my current setting, and nRF52DK goes to bootloader mode directly.

Are you able to run your application code? 

[Hung Bui]

Please make sure you use --bl-settings-version 2 and you also have 

• Change NRF_DFU_BLE_REQUIRES_BONDS to 1
• Change NRF_SDH_BLE_SERVICE_CHANGED to 1

in your application and in your bootloader. 

To enable debugging, if you are using Segger embedded studio you would need to: 

- Project Option -> Code Generation -> Optimization Level = None

- Project Option -> Code Generation -> Debugging Level = 3

- Project Option -> Switch to Common instead of Debug/Release -> Preprocessor -> Preprocessor Definitions : add DEBUG in to the list. 

[Vick_Chang]

Hi Sudharsan,

After nrfjprog -f nrf52 --recover, download ble_app_hrs_pca10040_s132 by SES.

The app works fine. Nordic_HRM_DFU is shown in scan list (My other nRF52DK)