Having both U.FL and Trace Antenna with Zero Ohm resistor?

Question

We are thinking to evaluate both the U.FL and Trace Antenna options on a custom nRF52840 prototype board. 
 1. Referring to this discussion, point 3 is about provisioning two antenna types. I understand that by using zero ohm resistor i.e., by populating/de-populating the antenna type could be selected/unselected respectively. 
 2. However, in other discussion, leaving the resistor pads unconnected would impact the signal because the pads would act as transmission line. 
 
 Suggestion needed: 
 It's a 4 layer board, having calculated the trace-width for 50-ohm impedance matching trace using the parameters of the PCB fabricator. I have replicated the nRF52840-DK trace antenna and SWF connector connections. 
 1. I can think of this simple circuit with 0-ohm (R31 & R35) in series on both the antenna lines: (I need a suggestion for PCB layout for this circuit). With this approach, I guess the 0-ohm resistor would have a negative impact on RF signal because it would impact the 50-ohm impedance matching trace. 
 
 2. The other option, is to have two LC networks as seen above with 0-ohm connected to nRF_ANT pin. 
 
 This is Work In Progress, replicating nRF52840 DK antenna and SWF connector traces:

Marjeris Romero · Accepted Answer

Hi Jaimin, 
 Very sorry for the lack of reply on this post. I found it in my queue today. Using a 0R resistor to choose between antennas is a very common design choice amount our customers, nothing wrong with that, but you need to be aware on how you are placing the 0R resistor so you don't create an open stub as it's mention in https://devzone.nordicsemi.com/f/nordic-q-a/27478/is-50-ohm-maintained-at-ufl-connector/108532#108532 In the discussion above my recommendation to the customer would be to move R7 to the right so you can solder one pad of the resistor directly on the RF path coming from the ANT pin, this way you will not have the stub coming out of the RF path when the resistor is desoldered: 
 And also add a series resistor on the RF path as well as it's describe on the same answer on the case above: "Use two components in a T-junction configuration to choose between either antenna or conductor. You should then try to keep it as small as possible, and keep in mind that parasitics from the resistor could affect your match." 
 In the case of the module on your picture I am supposing the feeding line from the ANT pin is coming from under the module: 
 
 This looks like an OK solution but having a 90 degrees on the RF path can also potentially create other challenges because of reflections on the RF path. The best solution as discussed in case ID 27478 would be using a connector with a built in switch placed as part of the transmission line leading out to the antenna as used in the nRF52840 DK, but if not possible I think both option 1 (as long as the resistors are placed close to each other so the stubs are minimized) and option 2 (with 90 degrees RF paths) are OK solutions. About your other question: 
 1. I can think of this simple circuit with 0-ohm (R31 & R35) in series on both the antenna lines: (I need a suggestion for PCB layout for this circuit). With this approach, I guess the 0-ohm resistor would have a negative impact on RF signal because it would impact the 50-ohm impedance matching trace. 
 You cannot have 2 radio matching networks (as seen in option 2), as you need to placed the radio matching components very close to the ANT pin and follow the spacing and dimentions shown in the reference design as close as possible, so you need to go for alternative 1: 
 nRF_ANT pin > Radio matching components > T-junction of 0R to choose between antenna and uFL connector (if not using a switching connector) > antenna Best regards, 
 Marjeris

Having both U.FL and Trace Antenna with Zero Ohm resistor?

Top Replies