Current consumption on NRF52833 is too large

Question

Hi, I now aply ble_app_uart example for my custom board My board work perfect Some configurations in my code based on ble_app_uart Advertising_interval : 64ms Tx: 0 Some changes compared to original ble_app_uart example 
 /**< CONFIG BLE PARAMETERS*/
#define APP_BLE_CONN_CFG_TAG 1 /**< A tag identifying the SoftDevice BLE configuration. */
#define NUS_SERVICE_UUID_TYPE BLE_UUID_TYPE_VENDOR_BEGIN /**< UUID type for the Nordic UART Service (vendor specific). */
#define APP_BLE_OBSERVER_PRIO 3 /**< Application's BLE observer priority. You shouldn't need to modify this value. */
#define APP_ADV_INTERVAL 64 /**< The advertising interval (in units of 0.625 ms. This value corresponds to 40 ms). */
#define APP_ADV_DURATION 0 /**< The advertising duration (180 seconds) in units of 10 milliseconds. */
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(20, UNIT_1_25_MS) /**< Minimum acceptable connection interval (20 ms), Connection interval uses 1.25 ms units. */
#define MAX_CONN_INTERVAL MSEC_TO_UNITS(75, UNIT_1_25_MS) /**< Maximum acceptable connection interval (75 ms), Connection interval uses 1.25 ms units. */
#define SLAVE_LATENCY 0 /**< Slave latency. */
#define CONN_SUP_TIMEOUT MSEC_TO_UNITS(4000, UNIT_10_MS) /**< Connection supervisory timeout (4 seconds), Supervision Timeout uses 10 ms units. */
#define FIRST_CONN_PARAMS_UPDATE_DELAY APP_TIMER_TICKS(5000) /**< Time from initiating event (connect or start of notification) to first time sd_ble_gap_conn_param_update is called (5 seconds). */
#define NEXT_CONN_PARAMS_UPDATE_DELAY APP_TIMER_TICKS(30000) /**< Time between each call to sd_ble_gap_conn_param_update after the first call (30 seconds). */
#define MAX_CONN_PARAMS_UPDATE_COUNT 3 /**< Number of attempts before giving up the connection parameter negotiation. */
#define DEAD_BEEF 0xDEADBEEF 

static void advertising_init(void) {
 uint32_t err_code;
 ble_advertising_init_t init;
 memset(&init, 0, sizeof(init));
 init.advdata.name_type = BLE_ADVDATA_FULL_NAME;
 init.advdata.include_appearance = false;
 // init.advdata.flags = BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE;
 init.advdata.flags = BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;
 init.srdata.uuids_complete.uuid_cnt = sizeof(m_adv_uuids) / sizeof(m_adv_uuids[0]);
 init.srdata.uuids_complete.p_uuids = m_adv_uuids;

 init.config.ble_adv_fast_enabled = true;
 init.config.ble_adv_fast_interval = APP_ADV_INTERVAL;
 init.config.ble_adv_fast_timeout = APP_ADV_DURATION;

 init.config.ble_adv_slow_enabled = true;
 init.config.ble_adv_slow_interval = APP_ADV_INTERVAL;
 init.config.ble_adv_slow_timeout = 0;

 init.evt_handler = on_adv_evt;

 err_code = ble_advertising_init(&m_advertising, &init);
 APP_ERROR_CHECK(err_code);

 ble_advertising_conn_cfg_tag_set(&m_advertising, APP_BLE_CONN_CFG_TAG);
}
 I expected current consumption is about 0.5mA But I got 20mA for this application on my board I only changed some configurations I atttached above compared to originanal ble_app_uart example Here is my schematic Here is the link of datasheet of my nRF52833 module http://en.abluetech.com/uploads/soft/201608/PTR9813_EngV1.11.pdf I use ptr981x nRF52833 module