• State Not Answered
  • Replies 8 replies
  • Subscribers 70 subscribers
  • Views 1381 views
  • Users 0 members are here
Attachments (0)
Nordic Case Info
  • Case ID: 294341
Options

Can't Update the Thingy:53 Firmwares, nor Connect it to Edge Impulse

gap_guillen

I have not been successful to updating the firmware of the Thingy:53 board, and I have tried all methods indicated here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_thingy53_gs.html

1. Updating through Bluetooth LE: The preloaded Edge Impulse firmware fails to connect, so I tried to update it with the nRF Programmer mobile app. After 10 attempts I managed to update it, however it still can't connect to Edge Impulse.

2. Updating through USB: This method fails for any firmware that I want to update, since it indicates the message "Error when fetching device versions...", so it does not activate the Write icon.

3. Updating through external debug probe: Following the steps in this method gives me this confusing message with the thingy:91 board:

Please update the firmwares of this board. I found a similar issue that was reported two months ago, and it doesn't seem to be solved:  Problem with Getting started with Thingy:53 

Kind regards

Parents
  • 0

    Hi, 

    1. Can you see the thingy53 advertise as EdgeImpulse with the nRFConnect mobile app? What do you use to connect Edge Impulse? Please try with nRF Edge Impulse.

    2. Remove the top cover on the thing53 and Press SW2 while switching SW1 to the ON position. 

    3. Please use nRF5340DK and select the file under hci_rpmsg/merged_CPUNET.hex and zephyr/merged_CPUAPP.hex  Edge_Impulse folder. 

    Regards,
    Amanda

  • 0 in reply to Amanda Hsieh

    Hi Amanda! Thanks for your tips. 

    1. Today, the Thingy:53 board is not detected by the nRF Programmer application. 

    Two days ago I could see the Nordic board, but now I can't. 

    Before upgrading any firmware, I tried to connect this thingy:53 to Edge Impulse via PC-serial port with command "edge-impulse-daemon" and it didn't connect.

    So I used the App to update the firmwares.

    First I updated the firmware "Pheriperal LBS" and everything was OK, the board could be detected without problems and the LED was flashing.

    The problem was when I updated the Edge Impulse firmware. The App and the Thingy:53 board were easily disconnected, it seems that there were conflicts to communicate via BT, and after many attempts I was able to upload the firmware and now the Thingy:53 board can´t be detected by the App.

    2. But when I connect the Thingy:53 board with the PC, it can be detected by the serial port.

    3. I followed your instructions. When I tried to install Edge Impulse firmware using this compressed file "2022-08-03-precompiled-application-firmware.zip" provided on the Nordic website, I got the error below:

    And the "Write" icon was not activated.

    But when I useed the firmware found on the Edge-Impulse website (nordic-thingy53-full.zip), I got this message:

    There is no error and the "write" icon is not active either.

    That is all! Your instructions are correct, but something is wrong with this Thingy:53 board. Maybe U uploaded a corrupt firmware. I don't know. If this board could be reseted to the factory mode.

    Kind regards

    Guillermo

Reply
  • 0 in reply to Amanda Hsieh

    Hi Amanda! Thanks for your tips. 

    1. Today, the Thingy:53 board is not detected by the nRF Programmer application. 

    Two days ago I could see the Nordic board, but now I can't. 

    Before upgrading any firmware, I tried to connect this thingy:53 to Edge Impulse via PC-serial port with command "edge-impulse-daemon" and it didn't connect.

    So I used the App to update the firmwares.

    First I updated the firmware "Pheriperal LBS" and everything was OK, the board could be detected without problems and the LED was flashing.

    The problem was when I updated the Edge Impulse firmware. The App and the Thingy:53 board were easily disconnected, it seems that there were conflicts to communicate via BT, and after many attempts I was able to upload the firmware and now the Thingy:53 board can´t be detected by the App.

    2. But when I connect the Thingy:53 board with the PC, it can be detected by the serial port.

    3. I followed your instructions. When I tried to install Edge Impulse firmware using this compressed file "2022-08-03-precompiled-application-firmware.zip" provided on the Nordic website, I got the error below:

    And the "Write" icon was not activated.

    But when I useed the firmware found on the Edge-Impulse website (nordic-thingy53-full.zip), I got this message:

    There is no error and the "write" icon is not active either.

    That is all! Your instructions are correct, but something is wrong with this Thingy:53 board. Maybe U uploaded a corrupt firmware. I don't know. If this board could be reseted to the factory mode.

    Kind regards

    Guillermo

Children
Related