Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hello!
I want to connect the MCP9808 with the nrf52832. Therefor I use i2C.
My example on the nrf52832 is the:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral\experimental_ble_app_eddystone...
We're quite interested in producing an nRF52 design based on the solar beacon (great design, and clean software). I appreciate the relative simplicity and manageable BOM cost...
Hello,
I am developing a system that samples 3 independent data using SSADC. since the timing was important in my system, I decided to use PPI to trigger the SSADC.
However...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello all
I am trying to implement hardware flow control for UART.
is there anything else to be done ? I have done the GPIO configurations like this
const app_uart_comm_params_t...
Hi,
I'm trying to migrate from SDK 6.1 to SDK 7.2 on custom board.
In SDK 6.1 everything works fine (SoftDevice v7.1.0), but with SDK 7.2 I get into HardFault Handler...
Hi My project need to transport HRM data by ANT+/BLE. base on ANT_s332_nrf52_0.9.1.alpha.hex and sdk nRF5_SDK_11.0.0_89a8197 platform. We have finished the function. Now we...
Hi all,
I know that there is a field "address type (public/random)" in white list.
When a scanner send scan request to an advertiser with public device address. this...
I have used the nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_proximity\pca10028\s130\armgcc for my project before I had the final PCB. I have tested my code on...
Hello,
I was wondering why I am not getting a theoretical sampling rate as I set them to with a timer.
I am using PPI to trigger a SAADC sampling with the timer to set...
Hello!
Nordic UART Service (NUS) is a pretty handy way of implementing a serial data transfer service over BLE. The nRF Toolbox on Android makes it very easy to test it...
Hi,
While this is not related to Nordic Semiconductor products, I think we should incorporate Captcha system during user registration. We had some spam in the morning and...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
is there any example how to reset the hole device? Are there any example codes for using something like system_off or system_on ?
Best regards Nils
using S130, SDK11,
when it connected the heart rate sensor A and eveything is OK.
but when it disconnected the sensor A and connected the sensor B
the connecting...