Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hi!
Turns out that there is no need for the SD310 and the nRF bootloader. Which means that the flash layout is edited and current support for the BLE OTA is dropped since...
Hi,
I am working on nRF51822 Microcontroller. I am not using any kind of stack I mean Bluetooth etc. I have a simple nRF51822 microcontroller and am running a simple application...
Like the title says, I'm making a call to nfc_t2t_emulation_start, and getting NRF_ERROR_INVALID_STATE (0x08) back.
The only prerequisite that I'm aware of in order to...
I'm testing with S132 nRF52 SoftDevice 3.0.0, BLE dfu operation with single, nRF toolbox on Android version 1.16.5.
I have checked the example in SDK, nRF5_SDK_12.1.0_0d23e2a...
Hi,
I am trying to make communication between two nrf51822 modules. I am using nrf11 SDK, In this i am using proprietary_rf-> esb_low_power_prx(ptx) examples.
In this...
URGENT
First of all, I have to mention that I dont understand PPI.
I have application which uses PWM to control a pump which is connected to the nRF52. To the nRF52...
What would be the payload size? That is, without any ble involvement? I assume it's 31 bytes? Or maybe this question is invalid since you can transfer unpackaged, raw data...
Issue: when the battery level is requested for the first time from mobile its responding correctly. but, when it is requested for the second time from mobile, disconnection...
We are trying to import blinky example(Keil project) to SES, we could succesfully build the eaxmple and dump into nRF52-DK, example is from SDK12.1. After we dump into kit...
Hi, I'm planning to create a custom PCB that uses nRF52832-QFAA.
Currently, I chose the Q22FA12800025 32MHz crystal to use, which is the same one in the PCA10040, I believe...
Hi,
I use nRF51822 with 256k flash and external sensor, and i want to write the data i receive from it via SPI to internal flash?
After the data received i want to send...
I've seen a few posts in regards to the usage of MCP in a windows virtual machine. From what I can gather, this setup just will not work, however I haven't really seen an...
Hello:
I was wondering about the random addresses programmed into the FICR on some of the devboards that I have. I read the devzone and it appears that the DEVICEADDR is...
I read that the DEVICEADDR is always in the advertising packet, so i need to take these data from the master each time that a slave is conected to them. I trying do something...
